Panasonic TH-65PB2W Setup of Screensaver Time, Screensaver For preventing image retention

Page 38

Screensaver (For preventing image retention)

Setup of Screensaver Time

After selecting Time Designation, Interval or Standby after SCR Saver, the relevant Time Setup will become available for selection and the Operating Time may be set. (Time cannot be set when “Mode” is “On” or “Off”.)

Press to select Start Time / Finish Time (when Time Designation is selected).

Press to select Periodic Time / Operating Time (when Interval is selected).

Press to select Screensaver duration

(when Standby after SCR Saver is selected). Press to setup.

button: Forward button: Back

Notes:

•Pressing “ ” or “ ” button once changes the Time 1 minute.

[However, switching occurs every 15 minutes when Periodic Time is selected.]

•Pressing “ ” or “ ” button continuously changes the Time by 15 minutes.

•“Screensaver duration” of the “Standby after SCR Saver” can be set from 0:00 to 23:59. When this is set to “0:00”, “ Standby after SCR Saver” will not be activated.

Note: Timer function will not work unless “Time” is set.

Screensaver

 

 

Start

Time

15:00

Scrolling bar only

 

Function

 

Mode

Time Designation

 

Start Time

6:15

 

Finish Time

12:30

 

Screensaver

 

 

Start

Time

15:00

Scrolling bar only

 

Function

 

Mode

Interval

 

Periodic Time

12:00

 

Operating Time

3:00

 

Screensaver

 

 

Start

Time

15:00

Scrolling bar only

 

Function

 

Mode

Standby after SCR Saver

 

 

 

Screensaver duration

6:15

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Operating Instructions Display Operations Table of Contents Trademark Credits Important Safety NoticeImportant Information Do not place any objects on top of the Plasma Display Safety PrecautionsSetup Transport only in upright positionIf problems occur during use Safety PrecautionsWhen using the Plasma Display Electric shocks can result if this is not done Do not burn or breakup batteriesRemote Control Batteries AccessoriesAccessories Supply Connections AC cord connection and fixing, cable fixingConnections Speaker connectionVideo equipment connection Video and Component / RGB in connection Hdmi connection DVI-D Input ConnectorSignal Name DVI-D in connectionSignal Names for Mini D-sub 15P Connector PC Input Terminals connectionComputer CommandSerial Terminals connection Communication parametersPower On / Off Starting up the networkPower On / Off PC Network Whiteboard Slot Input Video Component Hdmi DVI Selecting the input signalPC Network Whiteboard Video COMPONENT* Hdmi DVI Slot Input Input terminal in Terminal BoardBasic Controls Remote control sensorInput button Input signal selection see Brightness SensorECO Mode ECO Basic ControlsAll Aspect mode Aspect ControlsDigital Zoom Using Two Screen Display Multi PIP SettingsPIP Mode On-Screen Menu Displays Auto mode Adjusting Pos./SizeUsing Remote Control Adjusting Pos./Size Adjust so that any such noise is minimizedIs adjusted as follows For 2k1k signals Clamp Position During Component/PC input signalOptimum value for Clamp Position adjustment 2k1kPicture Adjustments Advanced settings Picture AdjustmentsPicture Profiles MY Picture MEMORY1Example Specifying MY Picture Saving profilesPicture Profiles Select All deleteDeleting profiles Loading profilesEditing profiles Renaming profilesSound Adjustment SDI Sound OutputSetup menu screen Setup menuNetwork Setup On/Off Timer Setup Day/Time Setup / On/Off Timer SetupDay/Time Setup Touch-Pen Settings Slot Input NetworkPairing Touch-Pen SettingsStandby pen charging mode UnpairingMulti PIP Settings Multi PIPScreensaver For preventing image retention Mode selectionStart setting Function selectionSetup of Screensaver Time Screensaver For preventing image retentionReduces screen image retention Extended life settingsPicture Mode Contrast Image Retention Reduction MenuReduces screen image retention Express settingsNanodrift Mode Nanodrift SaverAdjust Custom settingsReset Set each menu SelectECO Mode settings ECO ModeCustomizing the Input labels Function Button Settings Input SLOT* Input WhiteboardOSD Language No activity power offMenu Display Duration / OSD Brightness Display orientationYUV / RGB-in select Setup for Input SignalsComponent / RGB-in select Component RGBSignal menu Setup for Input SignalsSync Setting RGB sync signalSetting Component sync signal SDI ThroughAdvanced NR Input signal displayNoise reduction Sets the three NR functions separatelyOptions Adjustments Press for more than 3 seconds. Press to select OptionsOptions Adjustments Input lock SeeStudio Gain Weekly Command Timer NormalisationCommand setting screen Press to select a command numberPress to select Command No Press to select Time / CommandAudio input select When the menu is not displayed normal screen Set Touch Panel mode to On Select AdjustCalibration mode Hold down for over 3 secondsPC Network Slot Input Video Component Hdmi DVI Input SearchInput Search Primary Input, Secondary InputTroubleshooting Plasma Display panelList of Aspect Modes 149Applicable Input Signals Mark Applicable input signalVideo input Video Applicable Input SignalsShipping condition Command list of Weekly Command Timer Specifications TH-50PB2W TH-65PB2WThis product incorporates the following software Customer’s Record
Top Page Image Contents