Panasonic PT 47WXD64 Convergence Procedure, Cable Module Info, Center of cabinet, as shown below

MENU OPERATIONS

Convergence (cont.)

Note: Convergence seldom needs adjusting except after moving the PTV or to make minor adjustments.

Procedure

•Press OK to enter convergence sub-menu field.

• Press CH or CH to select:

•CONVERGENCE ADJ. - Select to correct minor convergence problem.

Note: After selecting, press OK to continue

CONVERGENCE ADJ.

•RESET TO DEFAULT - Select to set convergence to factory default setting.

Note: After selecting, press OK to activate RESET TO DEFAULT feature.

Convergence	SELECT	OK
Convergence Adj.
Reset to Default	MENU	EXIT
	to return

CONVERGENCE ADJ.

Procedure

•After pressing OK the align Green to Center screen will be displayed.

•Then use the navigation buttons on the remote control to align the horizontal and vertical green lines on screen, with the cabinet reference marks on top center and left

center of cabinet, as shown below.

Reference Marks

	Press CH And VOL Key To
	Align Green Lines To The
	Center Mark On The Cabinet
		Up	Right
	Left
		Down
Front of cabinet	Press Ok To Continue

•Press OK button to display red center correction screen.

•Use the navigation buttons on the remote control to align the red cross with the white cross pattern at the center of the screen.

Note: To prevent picture tube damage do not leave test pattern on for an extended period of time.

•Then press “0” on the remote control keypad to display the BLUE center correction screen, repeat procedure for adjusting blue. If needed press “0” again to return to RED correction screen.

Note: An adjusted cross pattern appears white with a minimum of color protrusion.

If Red Is Protruding From					If Blue Is Protruding From
Center Cross, Press CH And					Center Cross, Press CH And
VOL Key To Correct				Press	VOL Key To Correct
		Up			Up
				“0”
	Left		Right		Left	Right
		Down			Down
PRESS 0 To Adjust Blue					PRESS 0 To Adjust Red
Press Ok To Continue					Press Ok To Continue

NINE POINT CONVERGENCE CORRECTION

Note: Remote Control must be in TV mode.

Procedure

•Press OK button to display red correction screen.

•Press the 1 through 9 keypad buttons on the remote control to select the desired convergence position.

•Use the navigation buttons to align the RED cross with the white cross pattern.

Note: An adjusted cross pattern appears white with a minimum of color protrusion.

1	2	3
	Press # Key To Select Pos.
Press CH And VOL Key To Corr.
4		6
	Correcting Red
	Press 0 To Adjust Blue
	PRESS ACTION TO EXIT
	Press Ok To Exit
7	8	9

•Press “0” on the remote control keypad to display the BLUE correction screen, then repeat procedure.

1	2	3		1	2	3
	Press # Key To Select Pos.				Press # Key To Select Pos.
Press CH And VOL Key To Corr.			Press	Press CH And VOL Key To Corr.
4		6		4		6
			“0”
	Correcting Red				Correcting Blue
	Press 0 To Adjust Blue				Press 0 To Adjust Red
	PRESS ACTION TO EXIT				PRESS ACTION TO EXIT
	Press Ok To Exit				Press Ok To Exit
7	8	9		7	8	9

•To exit convergence screen press OK button, then press EXIT to quit all menus.

Cable Module Info

This menu is used to provide information when a CableCARD™ is inserted into the CableCARD™ INTERFACE slot on the back of the projection television. If no CableCARD™ is present and you try to access the Cable Module Info, the message ‘Cable Module Not present’ will be displayed on screen. To receive the features offered by your cable company, you may have to subscribe to those services.

Note: Please contact your cable company regarding availability of the CableCARD module. The CableCARD module is needed to receive premium digital services (where available) through the cable input. You may also able to order call-ahead pay per view events.

ENGLISH

29z