Panasonic PT 47WXD64 Digital Audio Out Connection, Amplifier Connection Analog, Audio Adjustments

OPTIONAL EQUIPMENT CONNECTIONS

Digital Audio Out Connection

Use the diagram below to connect the Digital Audio Output of your HDTV Projection Television to a Dolby Digital decoder.

Digital Audio Out

Dolby Digital 5.1 channel surround sound delivers digital-quality sound. Dolby Digital provides five discrete full-bandwidth channels for front left, front right, center, surround left and surround right, plus a LFE (Low Frequency Effect) subwoofer channel. For a full Home Theater sound experience, an external Dolby Digital decoder and a multichannel amplifier must be connected to the Digital Audio Out jack on the PTV.

•	Program Out signal may not be available when
	component input is selected for main picture.
•	Program Out signal is available when receiving digital
	channel. However, all digital formats are down converted
	to composite NTSC video.
•	When receiving digital or analog channels signals and
	the analog or digital CC is ON, Program Out connector
	will output open caption text in the NTSC video picture. If
	CC is OFF, only analog CC closed caption code is
	passed out the Program Out connector.
•	Certain program content output from the Program Out
	connector may have the Macrovision signal modification
	applied to its signal, preventing VCRs from recording this

ANT A

Cable In

ANT B		TERMINALS ON BACK OF PROJECTION TELEVISION
		VIDEO
CableCARDTM	HDMI	Y
INTERFACE				￿	￿
SERVICE	A/V IN	PB				S-VIDEO
								Six channel Speaker system
ONLY
		PR						VIDEO
		L						L
		R						R
	L	1	2
		AUDIO COMPONENT		INPUT	INPUT	INPUT	PROG	TO AUDIO
		VIDEO INPUT		1	2	3	OUT	AMP

AUDIO IN

Amplifier

90.7 MHZ

OPTICAL IN

video signal.

Amplifier Connection (Analog)

To listen the audio through a separate stereo system, connect an external audio amplifier TO AUDIO AMP outputs on back of television.

Note: TO AUDIO AMP terminals cannot be connected directly to external speakers.

DIGITAL AUDIO OUT

R

CABLES NOT SUPPLIED

ANT A

Cable In

Procedure

•Connect the Digital Audio cable from the Digital Audio Out jack on the PTV to the Digital Audio In connection on the Dolby Digital decoder.

Note: When ATSC channel is selected, the output from the Digital Audio Out jack will be Dolby Digital. But, if NTSC

ANT B		TERMINALS ON BACK OF PROJECTION TELEVISION
		VIDEO
CableCARDTM	HDMI	Y
INTERFACE				￿	￿
SERVICE	A/V IN	PB				S-VIDEO
ONLY		PR					VIDEO		EXTERNAL AMPLIFIER
		L					L
		R					R		90.7 MHZ
	L	1	2
		AUDIO COMPONENT		INPUT	INPUT	INPUT	PROG	TO AUDIO	CABLES NOT SUPPLIED
		VIDEO INPUT		1	2	3	OUT	AMP

AUDIO IN

channel is selected, the output will be PCM.

DIGITAL AUDIO OUT

R

Program Out Connection (PROG OUT)

You can connect a VCR to the PROG OUT terminal to record the program you are viewing on-screen. An external monitor can also be connected to the PROG OUT and TO AUDIO AMP terminals. Connect the VCR as shown below.

ANT A

Cable In

ANT B		TERMINALS ON BACK OF PROJECTION TELEVISION
								VCR
		VIDEO
CableCARDTM	HDMI	Y							ANT OUT
INTERFACE				￿	￿			OUT
SERVICE	A/V IN	PB				S-VIDEO		VIDEO L - AUDIO - R
								IN	ANT IN
ONLY
		PR						VIDEO
		L						L
		R						R
	L	1	2
		AUDIO COMPONENT		INPUT	INPUT	INPUT	PROG	TO AUDIO
		VIDEO INPUT		1	2	3	OUT	AMP
	AUDIO IN
DIGITAL AUDIO OUT	R	CABLES NOT SUPPLIED

Procedure

•Connect the VCR to PROG OUT and TO AUDIO AMP terminals

•PROG OUT terminal display is the same as on-screen display.

•See the VCR instruction manual for further instructions for recording the program.

Notes:

•This TV contains Video and Audio Outputs for the purpose of recording television programming to VCR. Due to license restrictions, if a device (STB, DVD, etc.) is connected to the HDMI input of the TV, no video or audio output is allowed.

Audio Adjustments

•Select Speakers Off in Audio Other Adjust menu.

•Set amplifier volume to the preferred level.

10z