Panasonic AJ-HD1700 manual 121

Page 121

Error messages

Error messages

Display

• Description

• VTR operation and remedial action

 

 

 

 

 

FRONT LOAD

If the cassette fails to move up even after 6 seconds

MOTOR

have elapsed since the VTR transferred to the EJECT

 

mode, the AUTO OFF lamp lights, and the message

 

display blinks.

 

<Note>

 

If the cassette fails to move down even after 6 seconds

 

have elapsed since the cassette was inserted, the VTR

 

transfers to the EJECT mode.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

LOADING

If the unloading operation fails to be completed within 6

MOTOR

seconds, the AUTO OFF lamp lights, and the message

 

display blinks.

 

<Note>

 

If the loading operation fails to be completed within 6

 

seconds, the VTR transfers to the EJECT mode

 

(unloading mode).

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

REEL DIR

If the take-up reel motor is running in the reverse

UNMATCH

direction, the AUTO OFF lamp lights, and the message

 

display blinks.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

REEL

If an abnormal tension at the supply side is detected in

TENSION

the reel mode, the AUTO OFF lamp lights, and the

ERROR

message display blinks.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

SERVO COMM

When the servo microcomputer does not follow the

ERROR

instructions of the system control microcomputer even

 

after 10 seconds have elapsed, the AUTO OFF lamp

 

lights, and the message display blinks.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

SERVO

When

there is no response from the servo

CONTROL

microcomputer for 1 or more seconds, the AUTO OFF

ERROR

lamp lights, and the message display blinks.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

SERVO

When only the servo microcomputer was reset in an

ERROR

instantaneous power failure, etc., the AUTO OFF lamp

 

lights, and the message display blinks.

 

VTR:

Stops.

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

Display

• Description

 

• VTR operation and remedial action

 

 

 

 

 

 

 

 

 

 

 

S-FF/REW

When the tape start or end processing operation is not

 

TIMEOVER

completed, the AUTO OFF lamp lights, and

the

 

message display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

S REEL ROTA

If the supply reel motor rotates at an abnormally fast

 

TOO FAST

rate, the AUTO OFF lamp lights, and the message

 

display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

S REEL

If an abnormal torque applied to the supply reel motor

 

TORQUE ERR

is detected or if an abnormal current flowing to the

 

 

current-sensing resistor is detected, the AUTO OFF

 

lamp lights, and the message display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

T REEL ROTA

If the take-up reel motor rotates at an abnormally fast

 

TOO FAST

rate, the AUTO OFF lamp lights, and the message

 

display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

T REEL

If an abnormal torque applied to the take-up reel motor

 

TORQUE ERR

is detected, the AUTO OFF lamp lights, and

the

 

message display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

UNLOAD

If the tape has not been wound up during unloading,

 

ERROR

the AUTO OFF lamp lights, and the message display

 

 

blinks.

 

 

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

WINDUP

If, after the total tape amount has been detected, the

 

ERROR

amount of tape wound up onto the take-up reel and the

 

 

amount of tape supplied by the supply reel differ to an

 

 

abnormal extent while the tape is traveling, the AUTO

 

 

OFF lamp lights, and the message display blinks.

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

W-UP REEL

If, after the cassette has been inserted, the tape take-

 

NOT ROTA

up reel has not wound up the tape while the total tape

 

 

amount is not detected and while the tape is traveling,

 

 

the AUTO OFF lamp lights, and the message display

 

 

blinks.

 

 

 

 

VTR:

Stops.

 

 

• Set the POWER switch to OFF and then back to ON

 

again.

 

 

 

 

 

 

If the error message display persists even after the VTR has been shut down and started up again, consult your dealer.

121

Page 120 Page 122
Image 121
Page 120 Page 122
Contents VQT0E88 Model AJOperating precaution For your safetyIndicates safety information For Europe For U.S.A. and CanadaDo not Remove Panel Cover by UN Screwing FCC NoteHow to replace the fuse Contents General outline Standard accessoriesFeatures Front panel Parts and Their FunctionsFine mode Factory settingMonitor Select buttons Meter FULL/FINE selector buttonTime code display Adjust dialAudio Unity lamp @ Direct menu buttonsStill REVFWD Number keys Audio channel selector buttonPREVIEW/REVIEW button Auto Edit buttonFront panel Player and Recorder buttons Standby buttonInput Check button Video 59/60 Hz mode Input Check output specificationsVideo 50 Hz mode AudioTime code display TCG CTLUBG TCR/TRear panel @ SD REF in connectors and 75-ohm termination switches ? Analog Composite Video OUT connectorsHD REF in connectors and 75-ohm termination switches HD REF OUT connectorPlayer side ConnectionsSource side Recorder sideExample of system connections in 25 Hz SD mode Example of system connections in 23/24 Hz or 25 Hz HD modeExample of connections with an editing controller Cassettes Concerning tapesXL cassettes Dvcpro HD LPTurn on the VTR’s power Check that the Auto OFF lamp is off Turning on the power and inserting the cassettePrecautions for Still Timer setting Stop and Standby modesRecording Adjust the audio levelsPlayback Playback phase adjustment functionShuttle mode Jog modeVariable mode Jog/ShuttleManual Editing When the search mode is established on the CUE screenPreroll AssemSwitch the time counter display to TC Or CTL When using this VTR as the playerAutomatic Editing Basic editing steps are as followsRegistering the edit points Selecting the editing modePlayer RecorderChecking the edit points When no edit points have been setModifying edit points Re-registering an edit pointPostrolling Previewing Automatic editingRetry function Auto tag functionReviewing Registering the edit points Audio Split EditingClearing the edit points Modifying the edit pointsBetween the video in and OUT points Duration displayBetween the audio in and OUT points Match frame processing functionVariable memory function selection Variable memory functionOutline Variable memory playbackCleared HasEdited results can be checked VariableGeneral description Function menusGeneral menus Special menusAllocating the function keys Toggle How to switch the settingsToggle i ADJ PressStatus display HomePB FMT DvcamINT23 VTRINT24 INT2559.94 Hz/60 Hz, 50 Hz mode 59.94 Hz/60 Hz operation specifications for tape playback23.98/24Hz, 25 Hz HD mode Hz SD modeVariable memory mode indicator Operation mode speed displayRemaining tape/total tape display Cue time displaySelecting the values Registering TCG valuesInputting numbers and letters Entering the input valuesTape ResetOutput INH ALLPressed. Refer to setup menu items No.670 to Video signal output level adjustmentsVideo F4 Shift F1 Shift F2 Shift F3 ShiftF5 Shift HUEAudio Audio signal input selection CH1jCH4F1 SHIFT2 VolumeF2 SHIFT2 F3 SHIFT2 ReccueTimer DF MOD NDF DF Mode F1 ShiftTC SRC INT TC Source Extl Sltc Svitc INT Extl VitcMoving to registered points CUENumber display area Registered point display areaCue point registration When registering cue points by numberCUE Search operations Clearing registered points$ Clearing all the registered points together $Clearing individual registered pointsDiag Error log functionHour-meter display LCD monitor displaysMessages saved when on is selected as the setting Menu Automatic editing and manual editing AssembleAfter the edit in and OUT points have been Insert When the editing mode has been selectedAfter the edit Buttons lightSettings Setup MENU/SYSTEM MenuFlow of setting changes Setup Menu function buttonsFunction buttons File Lock File overwrite inhibit facilityUnlocked status FacilityPF1/PF2 Clearing all the function button settingsRegistration Clearing the menu itemsPF1/PF2 function buttons Flow of function button registrationPF1/PF2 function button names 401 400402 403701 700702 703File status CardSelecting the operation files inside the selected memory Selecting the targeted memoryAssign SaveLocking a file Editing the title of a selected fileSelect the file to be locked, and press Lock File statusItems which can be registered in the input and output pins Pins in which functions can be registered50P IN/OUT Assign Registered item namesClearing Resetting all the items and valuesSpecial OUT menu list Special in menu listTC input statuses Error statusesUp-conversion statuses Up-conversion down-conversion statusesFlow of registration 50P IN/OUT Assign function buttonsOr more Pin assignment factory settingsSystem menus Video output signal adjustmentsCoarse SYS HFine SYS SCFreq SCH SDMenu Lock Basic Setup menusSDI CharaPOS MoniFrequency PB FormatOUT REF HdrefOperation Lamp FRZ ModeEject SW INHAlarm Beep SP ModeEject Lamp KEY BeepInterface Edit CH3 CH2CH4 Edit RPLCE4Tape Protect Time Code Binary GP Phase CorrISO PAGE/LINEVideo Video OUT C ENH U/CStyle HUE StyleSetup LVL PhaseBright ContrastCC REC Video IndexAudio SEL34 SEL12SEL56 SEL78100 101 102 103 Audio outputs in the search modeConnections with Dolby-E* components MenuTo cancel the setting entered in , press How to switch the system frequencyHas been cleared, the following message appears VTR startsSystem menu and setup menu settings Menu management accompanying switching the system frequency50P IN/OUT 50-pin connector registration System menu107 Setup menusOUT REF Input Hdref Output Tape108 109 Thru Manu CC REC OFF BlankDigi PB Fade CUTTime code and user’s bit Setting the internal time codeTime code User’s bitTime code and user’s bit playback Concerning the time code and user’s bitThese functions work only on the HOME, PF1 and PF2 screens Cue-upSuperimpose screen Operation modeCharacters displayed Display positionAudio recording channels Selecting the audio recording channels and monitor outputMonitor output channels 114Been run at all for about 5 minutes Display saving functionRack mounting Keep the temperature inside the rack to betweenUnit can be mounted into a 19-inch standard rack 116Maintenance Video head cleaningCondensation Diag menu Error messagesDisplaying the Diag menu Displaying the warning information Turn the ADJ dial to move the cursor Displaying the hour-meter informationShown as a superimposed display 119120 Error messagesCAP Tension DEW121 Condition for acknowledging Commands from RS-232C interface Hardware specificationsExternal interface specifications RS-232C interfaceSend format Software specifications protocolController PC When the communication has ended successfully Error code tableSend command When the communication has ended unsuccessfullyCommands relating to operation control Command table125 126 Commands relating to inquiriesCTL/TC Data RequestCLS Microsoft QuickBASIC sample programVideo OUT Connector signalsAudio OUT RS-422A Remote 9PParallel Remote 50P Printed circuit boardsEncoder REMOTE15P Video Input Connectors SpecificationsVideo Output Connectors GeneralAudio Input Connectors Video signal adjustment ranges Cue TrackVideo Audio Digital AudioOptional Accessories Other INPUT/OUTPUT Signals132 133 Panasonic Broadcast Europe GmbH Panasonic Broadcast Europe
Related manuals
Manual 34 pages 11.06 Kb
Top Page Image Contents