Panasonic AJ-YA120AG manual Setting the user defaults

Page 25

Setup (initial settings)

3 Press the MENU-UP button or MENU-DOWN button to move the cursor to the LOAD position, and press the SET button.

The unit is set to the LOAD mode, and the LOAD screen appears on the video monitor.

SET–UP MENU

<LOAD>

2NO FACTORY USER (ALL)

USER (NOT SYSTEM)

4 Press the MENU-UP button or MENU-DOWN button to move the cursor to the FACTORY position, and press the SET button.

O When the cursor is moved to FACTORY and this operation is performed, all the settings except the SYSTEM menu settings are returned to the factory settings.

O When the cursor is moved to NO and this operation is performed, the display returns to the menu screen without restoring the factory settings.

5 Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position.

This completes the menu setting procedure.

Setting the user defaults

1 Set the LOCAL/MENU/REMOTE switch to the MENU position.

The unit is set to the menu setting mode, and the menu screen appears on the video monitor.

2 Perform the operations in steps 2 to 6 for “Setting method using the on-screen menus,” and change to the desired settings.

3 Press the RESET button.

The unit is now set to the default setting mode, and the default setting screen now appears on the video monitor.

SELECT MODE

2 0 ESCAPE

1LOAD

2SAVE

3PROTECT

4

5

6

7

Press the MENU-UP button or MENU-DOWN button to move the cursor to the SAVE position, and press the SET button.

The unit is set to the SAVE mode, and the SAVE screen appears on the video monitor.

SET–UP MENU

<SAVE>

2NO

USER (ALL)

USER (NOT SYSTEM)

Press the MENU-UP button or MENU-DOWN button to move the cursor to the USER (ALL) position, and press the SET button.

O When the cursor is moved to USER (NOT SYSTEM) and this operation is performed, all the settings except the SYSTEM menu settings are updated.

O When the cursor is moved to NO and this operation is performed, the display returns to the menu screen without updating the settings.

The screen prompting the user to confirm whether the settings are to be saved now appears. To save the settings, press the MENU-UP button or MENU-DOWN button to move the cursor to the YES position, and press the SET button.

The settings are now stored in the memory.

SAVE OK?

2NO YES

Set the LOCAL/MENU/REMOTE switch to the LOCAL or REMOTE position.

This completes the menu setting procedure.

25

Image 25

Contents Model No. AJ- E Operating InstructionsOperating precaution For your safetyFor U.K. only Contents Introduction FeaturesMulti-functional interfaces Front panel Parts and their functionsRepeat lamp LOCAL/MENU/REMOTE switchSystem format lamp SCH lamp2? Analog lamp2 Audio monitor selector switch@ Meter button and lamp CH34 Audio output lamps CH12, CH34Volume control Analog audio signal recording level controls2720p lamp Headphone jackWhen the AJ-YA120AG or AJ-YAD120AG is installed REC button2 No optional board installedTAPE/EE switch Reset buttonAC in inlet Rear panelDC in socket DC OUT socketTC OUT connector TC in connector2HD/SD REF Video in connectors and 75Ω termination switch2 Audio in connectors CH1, CH2, CH3, CH42Tapes Precautions for using consumer DV and Dvcam cassettesInserting the tape Usable tapesStop mode Turning on the unit’s powerOperation Pause/recording follow-on recording RecordingCue/review PlaybackStill image playback Insert a cassette tape into the unit Press the Play buttonLinear 0.3k playback When AJ-A95 is connectedVariable speed playback Setting the repeat playback mode Setting the Begin and END pointsSet the VTR to the menu mode Repeat playbackTime code & user’s bit Setting the time codeTime code User’s bitSelect menu item No.531 UB Preset Setting the user’s bitPlaying back the time code and user’s bit T2R00 07 04Characters displayed Superimposed screen displaysRemaining tape display Display positionTime mode Operation modeSTA mode M modeSetting method using the on- screen menus Setup initial settingsReturning to the factory settings Set the LOCAL/MENU/REMOTE switch to the Menu positionSetting the user defaults Menu protection Loading the user defaultsDisplaying the Diag menu Releasing the menu protection modeWith the hour meter displayed, press the Search button Menus which are displayed Setup menusTYPE-B Near Audio in SEL Setting Description of settings Superimposed Display Indicates the factory settingSystem System Freq Setting Description of settingsHD SYS H ADV Basic Format Display PB Format SYS FormatManual Auto022 020 023 Playback format Formats for playbackManual Dvcam HD-LP Operation SP Mode INH FRZ Mode SELMemory Mode Auto REWBattery SEL Rept ModeCTL BGN TC BGNTape Protect InterfaceTime Code DF Mode Phase CorrTC Preset UB PresetVideo CCR Mode SD ESR Mode SDBLK Clip CC F1 BlankAudio CH1 REC CUECH2 CH3Menu DIF Speed DIF ConfigDIF in CH DIF OUT CHError No Error message and description Error messages23/24 Hz mode and 25 Hz mode Unload Error Operation performed by AJ-HD1200A CondensationMaintenance Video head cleaningProcedure to ejecting the tape manually in an emergency Emergency eject$ Video input connectors21 Specifications$ Video output connectors GeneralOptions Other ConnectorsMemo Panasonic Broadcast Europe Panasonic Marketing Europe GmbH