Panasonic AJ-YA120AG manual Video

Setup menus

VIDEO

	Item		Setting
				Description of settings
No.	Superimposed	No.	Superimposed
	display		display
600	VIDEO IN SEL			For selecting the video signals to be input.
		0000	INTSG	0: The internal signal selected by VIDEO INT SG is generated.
		0001	HDSDI	1: The serial video signal supplied to the HD SDI IN connector is selected.
		0002	1394	2: The compressed digital signals supplied to the DV connector are selected.
				When this happens, the audio input signals will also be supplied from the DV
				connector (digital video interface).
				<Notes>
				O This item’s setting cannot be changed while a tape is being played back.
				O When 1394 is selected as this item’s setting, “1080i” is selected as the menu
				item No.630 [1080i>HD_OUT] setting and “720p” is selected as the menu item
				No.632 [720p>HD_OUT] setting.
601	VIDEO INT SG			For selecting the type of internal signal.
		0000	100%CB	0: A 100% color bar signal is selected.
		0001	75%CB	1: A 75% color bar signal is selected.
		0002	SMPTE	2: An SMPTE color bar signal is selected.
		0003	BLACK	3: A black signal is selected.
		0004	PLL	4: The PLL signal is selected. (This signal is used for the adjustments performed
				before the unit was shipped from the factory.)
		0005	EQ	5: The EQ signal is selected. (This signal is used for the adjustments performed
				before the unit was shipped from the factory.)
602	SDI IN MODE			For selecting how to process the serial input.
		0000	DR OFF	0: The 8 higher bits whose two lower bits have been rounded off are recorded.
		0001	DR ON	1: The dynamically rounded 8 higher bit signal is recorded.
603	V-MUTE SEL			For setting whether to mute the video output signal when a blank part of the tape is
				detected during playback.
		0000	N MUTE	0: The video output signal is not muted. (It is frozen.)
		0001	GRAY	1: The video output signal is muted and turned gray.
		0002	BLACK	2: The video output signal is muted and turned black.
		0003	NOISE	3: The video output signal is muted and turned into noise.
604	FREEZE SEL			For selecting the freeze mode of the still pictures and the slow play mode.
		0000	FIELD	0: Field freeze, field slow
		0001	FRAME	1: Frame freeze, frame slow
615	V OUT SEL			For selecting what signals are to be output from the VIDEO OUT1 output
				connector.
		0000	CMPNT	0: The HD component signals are output.
		0001	CMPST	1: Composite signals are output.
616	OUT MATRIX			For selecting what signals are to be output from the HD component output
				connector.
		0000	YPbPr	0: The YPBPR signals are output.
		0001	RGB	1: The RGB signals are output.
620	DOWNCON			For setting the image processing during down-conversion.
	MODE	0000	FIT_V	0: Side cut mode
		0001	FIT_H	1: Letter-box mode
		0002	FIT_HV	2: Squeeze mode
621	UPCON V MODE			For setting the image processing during up-conversion.
		0000	FIT_V	0: Side panel mode
		0001	FIT_H	1: Top and bottom cut-off in vertical direction
		0002	FIT_HV	2: Stretch mode
626	D/C ENH H			For enhancing the horizontal outlines during down-conversion.
		0000	0dB	0: 0dB
		0001	+1dB	1: +1dB
627	D/C ENH V			For enhancing the vertical outlines during down-conversion.
		0000	0dB	0: 0dB
		0001	+1dB	1: +1dB

“” indicates the factory setting.

43