Panasonic AJ-YA120AG manual For U.K. only

Page 3

Caution for AC Mains Lead

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This product is equipped with 2 types of AC mains cable. One is for continental Europe, etc. and the other one is only for U.K.

Appropriate mains cable must be used in each local area, since the other type of mains cable is not suitable.

FOR CONTINENTAL EUROPE, ETC.

Not to be used in the U.K.

FOR U.K. ONLY

If the plug supplied is not suitable for your socket outlet, it should be cut off and appropriate one fitted.

FOR U.K. ONLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark Ï or the BSI mark Ì on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

WARNING: THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green-and-Yellow: Earth

Blue:Neutral

Brown:Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

•The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E or by the Earth symbol Ó or coloured GREEN or GREEN-AND-YELLOW.

•The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

•The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse

1. Open the fuse compartment with a screwdriver.

2. Replace the fuse.

Fuse

indicates safety information.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Model No. AJ- E Operating InstructionsOperating precaution For your safetyFor U.K. only Contents Introduction FeaturesMulti-functional interfaces Front panel Parts and their functionsSCH lamp2 LOCAL/MENU/REMOTE switchRepeat lamp System format lampAudio output lamps CH12, CH34 Audio monitor selector switch? Analog lamp2 @ Meter button and lamp CH34Headphone jack Analog audio signal recording level controls2Volume control 720p lampReset button REC button2 No optional board installedWhen the AJ-YA120AG or AJ-YAD120AG is installed TAPE/EE switchDC OUT socket Rear panelAC in inlet DC in socketAudio in connectors CH1, CH2, CH3, CH42 TC in connector2TC OUT connector HD/SD REF Video in connectors and 75Ω termination switch2Usable tapes Precautions for using consumer DV and Dvcam cassettesTapes Inserting the tapeTurning on the unit’s power Stop modeOperation Pause/recording follow-on recording RecordingInsert a cassette tape into the unit Press the Play button PlaybackCue/review Still image playbackWhen AJ-A95 is connected Linear 0.3k playbackVariable speed playback Repeat playback Setting the Begin and END pointsSetting the repeat playback mode Set the VTR to the menu modeUser’s bit Setting the time codeTime code & user’s bit Time codeT2R00 07 04 Setting the user’s bitSelect menu item No.531 UB Preset Playing back the time code and user’s bitDisplay position Superimposed screen displaysCharacters displayed Remaining tape displayM mode Operation modeTime mode STA modeSet the LOCAL/MENU/REMOTE switch to the Menu position Setup initial settingsSetting method using the on- screen menus Returning to the factory settingsSetting the user defaults Menu protection Loading the user defaultsReleasing the menu protection mode Displaying the Diag menuWith the hour meter displayed, press the Search button Menus which are displayed Setup menusTYPE-B Near Audio in SEL Indicates the factory setting Setting Description of settings Superimposed DisplaySystem Setting Description of settings System FreqHD SYS H ADV Basic Format Display Auto SYS FormatPB Format ManualFormats for playback 022 020 023 Playback formatManual Dvcam HD-LP Operation Auto REW FRZ Mode SELSP Mode INH Memory ModeTC BGN Rept ModeBattery SEL CTL BGNTape Protect InterfaceTime Code UB Preset Phase CorrDF Mode TC PresetVideo CC F1 Blank ESR Mode SDCCR Mode SD BLK ClipAudio CH3 REC CUECH1 CH2Menu DIF OUT CH DIF ConfigDIF Speed DIF in CHError messages Error No Error message and description23/24 Hz mode and 25 Hz mode Unload Error Operation performed by AJ-HD1200A CondensationEmergency eject Video head cleaningMaintenance Procedure to ejecting the tape manually in an emergencyGeneral Specifications$ Video input connectors21 $ Video output connectorsOptions Other ConnectorsMemo Panasonic Broadcast Europe Panasonic Marketing Europe GmbH
Top Page Image Contents