JVC 0302MNV*ID*JVE, LPT0649-001B VPS/PDC Recording, Enter the channel position, Press PR+

Page 25

EN 25

F Enter the channel position.

Press PR+/–.

G Set the tape speed.

Press SP/LP (p).

H Set the VPS/PDC mode.

Press VPS/PDC to select “ON” or “OFF”.

●If “VPS/PDC ON” is displayed on the TV screen, VPS/PDC is set to ON.

●If “VPS/PDC OFF” is displayed on the TV screen, VPS/PDC is

set to OFF.

 “VPS/PDC Recording” in the right column.

I Return to the normal screen.

After confirming all information is correct, press PROG or OK. “PROGRAM COMPLETED” appears on the TV screen for about 5 seconds, then the normal screen appears.

●Repeat steps 1 – 9 for each additional programme.

J Engage the recorder’s timer mode.

Press #(TIMER). The recorder turns off automatically and “#” appears on the front display panel.

●To disengage the timer mode, press #(TIMER) again.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 8, press WEEKLY (number key “9”) for weekly serials or DAILY (number key “8”) for daily serials (Monday – Friday). Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the button again makes the corresponding indication disappear.

NOTES:

●You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, “PROGRAM FULL” appears on the TV screen. To record

the extra programme, you must first cancel any unnecessary programmes ( pg. 26).

●If there is a conflict in the timer schedule and one programme overlaps with another, the programme starting earlier or programme with the lower programme number will be recorded.

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

ASet “L-2 SELECT” to “A/V” ( pg. 31).

BPerform steps 1 – 10. Enter “L-2” for the channel position in step 6.

CSet the satellite receiver to the appropriate channel before the selected programme begins.

DLeave the satellite receiver’s power on.

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed.

NOTES:

●When you use Express Timer Programming, set the start time (VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

●VPS/PDC recording is also possible when a satellite receiver or a cable system is connected to L-2 IN/ DECODER connector on your recorder.

●VPS/PDC recording is also possible via the L-1 IN/OUT connector.

How to check if the station being received transmits a VPS/PDC signal

APress – –:– – until the channel position appears on the front display panel.

BHold down START+ for about 5 seconds. “VPS/PDC” appears blinking on the TV screen.

If a VPS/PDC signal is detected from the station, “VPS/ PDC” will stop blinking.

If no VPS/PDC signal is detected from the station, “VPS/ PDC” will blink at a slower rate.

CPress – –:– – or START+ again to return to normal display.

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mains10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpConfirm/Set video channel With RF connection12 EN Results of Auto Set Up appear on the front display panelLanguage for the on-screen display Just ClockAccess the Country Set screen Access the Main Menu screenLanguage Return to the normal screen14 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 16 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection18 EN Tape Remaining Time Instant Timer Recording ITR20 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 22 ENEngage the recorder’s timer mode Set the VPS/PDC modeSatellite Receiver Users Guide Program Number Set24 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Access the Programme Check screen Disengage the timer modePress # TIMER, then press Return to the timer mode Cancel or change a programmePress # Timer 28 EN Another Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source playerIN/OUT connector Output Setting30 EN Select the input mode for the L-2 Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 34 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingOn or OFF  pg Is powered back onPreference. Normally select Auto Minimizes picture degradation during editing recording38 EN Entire programme while timer-recording in SP modeFor Example While the recorder is turned offAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen40 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetManual Channel Set 42 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations a 44 ENSet Stations B Station Name TV Station And ID ListAccess the Clock Set screen Access the Initial Set screenClock Set 46 ENSet Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation48 EN Video Channel SetGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program number50 EN TroubleshootingRecording 52 EN Other ProblemsPlayback 54 EN Express Timer Programming Auto Channel Set Auto Set UpTape Position Indicator Tape Remaining Time S.T. Picture System
Top Page Image Contents