JVC LPT0649-001B, 0302MNVIDJVE specifications 42 EN, Manual Channel Set

Page 42

42 EN

SUBSIDIARY SETTINGS (cont.)

Manual Channel Set

Store channels that were not stored during Auto Set Up ( pg. 10) or Auto Channel Set ( pg. 40).

A Access the Main Menu screen.

Press MENU.

B Access the Confirmation screen.

Press rt to move the highlight bar (pointer) to “MANUAL CH SET”, then press OK or e. The Confirmation screen appears.

C Select the channel position.

Press rt w e until an open (Example) To store in position 12.

position in which you want to store a channel begins blinking, then press OK. The Manual Channel Set screen appears.

The blueback screen and the programme currently being broadcast by the selected channel appear alternately for 8 seconds each.

D Select the band.

Press rt to change the band between CH (regular) and CC (cable), then press e.

E Input the channel.

Press the number keys to input the channel number you want to store.

●Input “0” before any single number entries.

●To input the registered station name (ID – pg. 45), press e until “– – – –” (ID setting) begins blinking, then press rt.

●For fine tuning adjustment, press euntil “+/–” begins blinking, then press rt. While tuning, “+” or “–” appears.

●When storing a channel that sends scrambled broadcasts, press e until “OFF” (Decoder setting) blinks, then press rt to set “DECODER” to “ON” (“OFF” is the default setting).

●When “L-2 SELECT” is set to “A/V” or “SAT”, the “DECODER” setting cannot be changed ( pg. 31).

F Enter new channel information.

Press OK and the Confirmation screen appears.

●Repeat steps 3 – 6 as necessary.

G Close the Confirmation screen.

Press MENU.

●To change positions, see “Change Station Channel Position” ( pg. 43).

●If you wish to set station names other than the ones registered in your recorder, see “Set Stations (B)” ( pg. 44).

ATTENTION

Guide Program numbers are not set when channels are stored manually. If an attempt is made at timer programming with the SHOWVIEW system in this state, the “GUIDE PROG SET” screen appears; set the Guide Program numbers on this screen. ( pg. 23, “ATTENTION — Guide Program Number Set”)

Or perform “Guide Program Number Set” ( pg. 49).

Image 42

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsConnect the recorder to TV Check the contentsSituate the recorder Connect the recorder to mainsTurn on the recorder Auto Set Up10 EN Select your countryConfirm/Set video channel Perform Auto Set UpSelect the language With RF connectionLanguage for the on-screen display Results of Auto Set Up appear on the front display panel12 EN Just ClockLanguage Access the Main Menu screenAccess the Country Set screen Return to the normal screenBasic Playback 14 ENPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackIndex Search 16 ENVariable Speed Search Skip SearchManual Tracking Next Function MemoryRepeat Playback Soundtrack Selection18 EN Instant Timer Recording ITR Tape Remaining TimeSuper VHS ET S-VHS ET Engage the S-VHS ET mode20 EN Receiving Stereo and Bilingual ProgrammesPlayback RecordingBefore performing the Showview Timer Programming Access the Showview screenAccess the Showview Program screen 22 ENSatellite Receiver Users Set the VPS/PDC modeEngage the recorder’s timer mode Guide Program Number SetExpress Timer Programming 24 ENEnter the channel position To Timer-Record Weekly Or Daily SerialsVPS/PDC Recording Press PR+Disengage the timer mode Access the Programme Check screenPress # TIMER, then press Cancel or change a programme Return to the timer modePress # Timer 28 EN Advantages of S-VHS video recorders Set the input mode of recording deckAnother Video Recorder Start the source playerOutput Setting IN/OUT connector30 EN Select and L-2 Input Setting Select the input mode for the L-2 Decoder connectorConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Connect the decoder Select the input mode34 EN Set the tunerConnecting/Using a Stereo System Make connectionsSelect the mode Mode SetAccess the Mode Set screen Select the mode settingPreference. Normally select Auto Is powered back onOn or OFF pg Minimizes picture degradation during editing recordingFor Example Entire programme while timer-recording in SP mode38 EN While the recorder is turned offAbout Ntsc Playback 40 EN Access the Auto Channel Set screenTuner Set Auto Channel SetPerform Auto Channel Set View the Confirmation screen42 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel44 EN Set Stations aSet Stations B TV Station And ID List Station NameClock Set Access the Initial Set screenAccess the Clock Set screen 46 ENSet the source channel position for clock data Set the date and timeSet Just Clock Start the clock operationVideo Channel Set 48 ENGuide Program Number Showview System SetupGuide Program Number Set Enter the Guide Program numberTroubleshooting 50 ENRecording Other Problems 52 ENPlayback 54 EN Tape Position Indicator Tape Remaining Time Auto Channel Set Auto Set UpExpress Timer Programming S.T. Picture System