JVC 0302MNV*ID*JVE, LPT0649-001B Perform Auto Channel Set, View the Confirmation screen

Page 41

EN 41

IMPORTANT

●In certain reception conditions, station names may not be stored correctly, and Auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the SHOWVIEW system, the recorder will record a TV programme of a different station. When programming the

timer using the SHOWVIEW system, be sure to check the desired channel is selected correctly ( pg. 22, “SHOWVIEW® Timer Programming”).

●Your video recorder memorizes all detected stations even if

reception of some of them is poor. You can delete those stations with an unacceptable picture ( pg. 43, “Delete A Channel”).

NOTES:

●Fine tuning is performed automatically during Auto Channel Set. If you want to perform tuning manually, refer to page 44.

●If you perform Auto Channel Set when the aerial cable is not connected properly, “SCAN COMPLETED –NO SIGNAL–” appears on the TV screen in step 7. When this happens, make sure of the aerial connection and press OK; Auto Channel Set will take place again.

●If no sound accompanies the picture or the audio sounds unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect.

Select the appropriate TV system for those channels ( pg. 43, “INFORMATION”).

F Perform Auto Channel Set.

Press OK.

●The Auto Set screen appears,

and remains on screen while

 

 

the recorder searches for

 

 

receivable stations.

 

 

As Auto Channel Set

 

 

progresses, the “q” mark on

 

 

the TV screen moves from

 

 

left to right. Wait until the TV

 

 

screen as shown in step 7

Beginning

End

appears.

 

 

G View the Confirmation screen.

After “SCAN COMPLETED” is displayed on the TV screen for about 5 seconds, the Confirmation screen looking like the one to the right appears. The stations your recorder located appear on a Confirmation screen —

channel positions (PR),

channels (CH) and station names (ID –  pg. 45). The blueback screen and the programme currently being broadcast by the blinking station appear alternately for 8 seconds each. To view the next page, use the rt w e button on the remote control.

●The stations located in the selected country appear at the top of the list.

●The Guide Program numbers will also be set automatically during Auto Channel Set.

H Return to the normal screen.

Press MENU.

●Using the Confirmation screen, you can skip or add channel positions, enter station names and perform other operations. Refer to pages 42 – 44 for the procedures.

●Depending on reception conditions, the stations may not be stored in order, and the station names may not be stored correctly.

●For information on scrambled broadcasts, refer to page 43.

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display Operating JVC TVs How To UseSituate the recorder Check the contentsConnect the recorder to TV Connect the recorder to mains10 EN Auto Set UpTurn on the recorder Select your countrySelect the language Perform Auto Set UpConfirm/Set video channel With RF connection12 EN Results of Auto Set Up appear on the front display panelLanguage for the on-screen display Just ClockAccess the Country Set screen Access the Main Menu screenLanguage Return to the normal screen14 EN Basic PlaybackHigh-Speed Turbo Search Slow MotionPause during playback Activate frame-by-frame playbackVariable Speed Search 16 ENIndex Search Skip SearchRepeat Playback Next Function MemoryManual Tracking Soundtrack Selection18 EN Tape Remaining Time Instant Timer Recording ITR20 EN Engage the S-VHS ET modeSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesRecording PlaybackAccess the Showview Program screen Access the Showview screenBefore performing the Showview Timer Programming 22 ENEngage the recorder’s timer mode Set the VPS/PDC modeSatellite Receiver Users Guide Program Number Set24 EN Express Timer ProgrammingVPS/PDC Recording To Timer-Record Weekly Or Daily SerialsEnter the channel position Press PR+Press # TIMER, then press Disengage the timer modeAccess the Programme Check screen Press # Timer Cancel or change a programmeReturn to the timer mode 28 EN Another Video Recorder Set the input mode of recording deckAdvantages of S-VHS video recorders Start the source player30 EN Output SettingIN/OUT connector Select the input mode for the L-2 Decoder connector Select and L-2 Input SettingSimple Connections Connecting To a Satellite ReceiverPerfect Connections 34 EN Select the input modeConnect the decoder Set the tunerMake connections Connecting/Using a Stereo SystemAccess the Mode Set screen Mode SetSelect the mode Select the mode settingOn or OFF  pg Is powered back onPreference. Normally select Auto Minimizes picture degradation during editing recording38 EN Entire programme while timer-recording in SP modeFor Example While the recorder is turned offAbout Ntsc Playback Tuner Set Access the Auto Channel Set screen40 EN Auto Channel SetView the Confirmation screen Perform Auto Channel SetManual Channel Set 42 ENDelete a Channel When Receiving a Scrambled BroadcastSet Stations B 44 ENSet Stations a Station Name TV Station And ID ListAccess the Clock Set screen Access the Initial Set screenClock Set 46 ENSet Just Clock Set the date and timeSet the source channel position for clock data Start the clock operation48 EN Video Channel SetGuide Program Number Set Showview System SetupGuide Program Number Enter the Guide Program number50 EN TroubleshootingRecording 52 EN Other ProblemsPlayback 54 EN Express Timer Programming Auto Channel Set Auto Set UpTape Position Indicator Tape Remaining Time S.T. Picture System
Top Page Image Contents