JVC LPT0649-001B, 0302MNVIDJVE specifications 52 EN, Other Problems

Page 52

52 EN			TROUBLESHOOTING (cont.)
OTHER PROBLEMS
	SYMPTOM	POSSIBLE CAUSE	CORRECTIVE ACTION
1.	Whistling or howling is heard from the	● The camcorder’s microphone is too	Position the camcorder so its microphone
	TV during camcorder recording.	close to the TV.	is away from the TV.
		● The TV’s volume is too high.	Turn the TV’s volume down.

2.	When scanning channels, some of	● Those channels have been designated to	If you need the skipped channels, restore
	them are skipped over.	be skipped.	them ( pg. 42).

3.	The channel cannot be changed.	● Recording is in progress.	Press 9 to pause the recording, change
			channels, then press 4 to resume
			recording.

4.	Channel settings that were made	● After the manual settings were made,	Perform manual setting again.
	manually seem to have changed or	Auto Channel Set was performed.
	disappeared.

5.	No channels are stored in the	● The TV aerial cable was not connected	Turn off the recorder once and connect
	recorder’s memory.	to the recorder when Auto Set Up was	the TV aerial cable to the recorder
		performed.	properly, then turn on the recorder again.
			Then perform Auto Set Up again
			( pg. 10).

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 52

Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsAuto Set Up 10 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languageConfirm/Set video channel With RF connectionResults of Auto Set Up appear on the front display panel 12 ENLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage Return to the normal screenBasic Playback 14 ENSlow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback16 EN Variable Speed SearchIndex Search Skip SearchNext Function Memory Repeat PlaybackManual Tracking Soundtrack Selection18 EN Instant Timer Recording ITR Tape Remaining TimeEngage the S-VHS ET mode 20 ENSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesPlayback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 22 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 24 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+Access the Programme Check screen Disengage the timer modePress # TIMER, then press Return to the timer mode Cancel or change a programmePress # Timer 28 EN Set the input mode of recording deck Another Video RecorderAdvantages of S-VHS video recorders Start the source playerIN/OUT connector Output Setting30 EN Select and L-2 Input Setting Select the input mode for the L-2 Decoder connectorConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 34 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingIs powered back on On or OFF pgPreference. Normally select Auto Minimizes picture degradation during editing recordingEntire programme while timer-recording in SP mode 38 ENFor Example While the recorder is turned offAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set40 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screen42 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a ChannelSet Stations a 44 ENSet Stations B TV Station And ID List Station NameAccess the Initial Set screen Access the Clock Set screenClock Set 46 ENSet the date and time Set Just ClockSet the source channel position for clock data Start the clock operationVideo Channel Set 48 ENShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberTroubleshooting 50 ENRecording Other Problems 52 ENPlayback 54 EN Auto Channel Set Auto Set Up Express Timer ProgrammingTape Position Indicator Tape Remaining Time S.T. Picture System