JVC LPT0649-001B, 0302MNV*ID*JVE specifications Video Channel Set, 48 EN

Page 48

48 EN

SUBSIDIARY SETTINGS (cont.)

Video Channel Set

Video channel (RF output channel) is the channel on which your TV receives picture and sound signals from the recorder through the RF cable.

IMPORTANT

Perform the following steps only if —

—Video Chennel Set has not been done correctly by the Auto Set Up function ( pg. 10),

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the recorder to your TV via the AV connection ( pg. 9), since you do not need the video channel you have to set the video channel to off.

If you have connected the recorder to your TV via the RF connection ( pg. 9), you have to set the correct video channel.

Before performing the following steps:

Make sure the recorder’s power is off and there is no cassette inserted in the recorder.

A Access the Video Channel Set mode.

Hold down 0 on the recorder until the front display panel shows the following.

B Set the RF output system.

The blinking number on the display indicates the RF output system of your country.

●If you have selected MAGYARORSZÁG, CESKÁ REPUBLIKA,

POLSKA or OTHER EASTERN EUROPE for the country setting ( pg. 10, 13), press rt to set to “2”.

●For other countries, set to “1”. Then press OK. (1: B/G 2: D/K)

Then set your TV to UHF channel 50.

●If the two vertical white bars appear clearly on the TV screen as shown to the right, go to step 4.

●If the two vertical white bars do not appear clearly, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

D Exit the Video Channel Set mode.

Press OK on the remote control.

C Set the video channel.

With AV Connection

Press PR – until the front display panel shows “1 – –” (or “2 – –”).

●Now the video channel is set to off.

With AV Connection

To view picture signals from the video recorder, set your TV to its AV mode.

With RF Connection

The channel on which the TV screen in step 3 appears clearly is your video channel.

To view picture signals from the video recorder, set your TV to the video channel.

With RF Connection

Press PR + or – to set the video recorder to a vacant channel between 22 and 69 which is not occupied by any local station in your area.

(Example) If channel 50 is available in your area

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Video Cassette Recorder Safety Precautions Moisture Condensation Front View Rear View Front Display Panel ON-SCREEN Display How To Use Operating JVC TVsCheck the contents Situate the recorderConnect the recorder to TV Connect the recorder to mainsAuto Set Up 10 ENTurn on the recorder Select your countryPerform Auto Set Up Select the languageConfirm/Set video channel With RF connectionResults of Auto Set Up appear on the front display panel 12 ENLanguage for the on-screen display Just ClockAccess the Main Menu screen Access the Country Set screenLanguage Return to the normal screenBasic Playback 14 ENSlow Motion High-Speed Turbo SearchPause during playback Activate frame-by-frame playback16 EN Variable Speed SearchIndex Search Skip SearchNext Function Memory Repeat PlaybackManual Tracking Soundtrack Selection18 EN Instant Timer Recording ITR Tape Remaining TimeEngage the S-VHS ET mode 20 ENSuper VHS ET S-VHS ET Receiving Stereo and Bilingual ProgrammesPlayback RecordingAccess the Showview screen Access the Showview Program screenBefore performing the Showview Timer Programming 22 ENSet the VPS/PDC mode Engage the recorder’s timer modeSatellite Receiver Users Guide Program Number SetExpress Timer Programming 24 ENTo Timer-Record Weekly Or Daily Serials VPS/PDC RecordingEnter the channel position Press PR+Disengage the timer mode Access the Programme Check screenPress # TIMER, then press Cancel or change a programme Return to the timer modePress # Timer 28 EN Set the input mode of recording deck Another Video RecorderAdvantages of S-VHS video recorders Start the source playerOutput Setting IN/OUT connector30 EN Select and L-2 Input Setting Select the input mode for the L-2 Decoder connectorConnecting To a Satellite Receiver Simple ConnectionsPerfect Connections Select the input mode 34 ENConnect the decoder Set the tunerConnecting/Using a Stereo System Make connectionsMode Set Access the Mode Set screenSelect the mode Select the mode settingIs powered back on On or OFF  pgPreference. Normally select Auto Minimizes picture degradation during editing recordingEntire programme while timer-recording in SP mode 38 ENFor Example While the recorder is turned offAbout Ntsc Playback Access the Auto Channel Set screen Tuner Set40 EN Auto Channel SetPerform Auto Channel Set View the Confirmation screen42 EN Manual Channel SetWhen Receiving a Scrambled Broadcast Delete a Channel44 EN Set Stations aSet Stations B TV Station And ID List Station NameAccess the Initial Set screen Access the Clock Set screenClock Set 46 ENSet the date and time Set Just ClockSet the source channel position for clock data Start the clock operationVideo Channel Set 48 ENShowview System Setup Guide Program Number SetGuide Program Number Enter the Guide Program numberTroubleshooting 50 ENRecording Other Problems 52 ENPlayback 54 EN Auto Channel Set Auto Set Up Express Timer ProgrammingTape Position Indicator Tape Remaining Time S.T. Picture System
Top Page Image Contents