JVC SR-VS30U manual 80 EN, Timer Recording

Page 80

Filename [VS30U_4-EN.fm]

 

VS30U_4-EN.fm Page 80 Thursday, January 31, 2002 3:45 PM

Masterpage:Left

80 EN

 

TROUBLESHOOTING (cont.)

TIMER RECORDING (cont.)

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

7.

Cable channels are not automatically

● The Controller is not properly

Connect the Controller correctly

 

switched during timer recording.

connected to the VCR.

( pg. 20).

 

 

● The output channel selected in the

After confirming your cable box’s output

 

 

Cable Box Set screen is incorrect.

channel number, re-access the Cable Box

 

 

 

Set screen and select the correct number

 

 

 

( pg. 21).

 

 

● The cable box is turned off.

Make sure the power is on before timer

 

 

 

recording starts.

 

 

 

 

8.

Satellite channels are not

● The Controller is not properly

Connect the Controller correctly

 

automatically switched during timer

connected to the VCR.

( pg. 23).

 

recording.

● The output channel selected in the DBS

After confirming your DBS receiver’s

 

 

 

 

Receiver Set screen is incorrect.

output channel number, re-access the

 

 

 

DBS Receiver Set screen and select the

 

 

 

correct number ( pg. 24).

 

 

● The VCR is not set correctly to control

Set the correct DBS receiver brand code

 

 

the DBS receiver.

( pg. 24).

 

 

● The DBS receiver is turned off.

Make sure the power is on before timer

 

 

 

recording starts.

 

 

 

 

9.

Timer recording begins as scheduled,

● Even though you do not use an external

Set “CABLE BOX SET” to “OFF”

 

but the channel is always incorrect.

cable box or DBS receiver, “CABLE BOX

( pg. 21) or “DBS RECEIVER SET” is set

 

 

SET” is set to “ON” or “DBS RECEIVER

to “OFF” ( pg. 24).

 

 

SET” is set to “ON”.

 

 

 

 

OTHER PROBLEMS

 

 

 

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

1.

Whistling or howling is heard from the

● The camcorder’s microphone is too

Position the camcorder so its microphone

 

TV during camcorder recording.

close to the TV.

is away from the TV.

 

 

● The TV’s volume is too high.

Turn the TV’s volume down.

 

 

 

 

2.

When scanning channels, some of

● Those channels have been designated to

If you need the skipped channels, restore

 

them are skipped over.

be skipped.

them ( pg. 19).

 

 

 

 

3.

The channel cannot be changed.

● Recording is in progress.

Press PAUSE (9) to pause the recording,

 

 

 

change channels, then press PLAY (4) to

 

 

 

resume recording.

 

 

 

 

4.

Channel settings that were made

● After the manual settings were made,

Perform manual setting again.

 

manually seem to have changed or

Auto Channel Set was performed.

 

 

disappeared.

 

 

 

 

 

 

5.

The Remote will not operate your TV

● The brand codes are set incorrectly.

Reset the correct brand codes ( pg. 67,

 

or cable box or DBS receiver.

 

68, or 69).

 

 

 

 

6.

Even though Auto or Semiauto Clock

● The clock setting data received from the

Select a different host channel during

 

Set has been performed, the clock is

host channel is incorrect.

“Semiauto Clock Set” ( pg. 17), or

 

incorrect.

 

perform “Manual Clock Set” ( pg. 17).

 

 

 

 

7.

No picture appears when you connect

 

Turn off the VCR or the connected

 

a device to DV IN/OUT connector.

 

appliance once, then turn it on again.

 

 

 

 

ATTENTION

This VCR contains microcomputers. External electronic noise or interference can cause microcomputer to malfunction. If the VCR does not operate correctly switch its power off and unplug the AC power cord from the AC supply. Wait for a while and then plug the power cord back in. Eject and check the condition of the cassette. If everything appears normal, you can operate the VCR as usual.

Page 80

January 31, 2002 3:45 pm

Page 79 Page 81
Image 80
Page 79 Page 81
Contents Video Cassette Recorder For Customer UseDear Customer Moisture CondensationImportant Product Safety Instructions Accessories Damage Requiring ServiceCleaning Replacement PartsContents Front View IndexRear View Symbolic Mode Indicators Front Display PanelHow To Use Remote10 EN ON-SCREEN Display for VHS deckTo recall an indication Press DISPLAY/OSDON-SCREEN Display for DV deck Check the contents Connect the VCR to power source12 EN Situate the VCRYou can obtain high-quality S-VHS pictures 8To connect to a TV with S-VIDEO/AUDIO input connectorsVideo Connection Perform Plug & Play setup What to do if Plug & Play setting failedPlug & Play Set 14 ENLanguage Access the Clock Set screen Clock Set16 EN PreparationsSemiauto Clock Set Manual Clock SetAccess the Tuner Set screen Tuner Set18 EN Auto Channel SetAccess the Manual Channel Set screen Manual Channel SetAdd or skip the desired channels To add channelsInstalling Controller 20 ENSetting cable boxs brand and channel Access the Cable Box Set screenAccess the Main Menu screen on the VCR Select the cable box’s channelIf the cable box’s channel does not change to 22 ENEnter the cable box’s brand DBS receiver If your DBS receiver has audio/video output connectorsHow to control the DBS receiver Setting DBS receivers brand and channel Turn on the DBS receiverSelect the DBS receiver’s channel If you do not use a DBS receiver, press rt until OFFController during timer recording Scheduled start time of timer recordingRecording Because it has no remote sensor, you cannot useBasic Playback VHS deckChoose a program Set the tape speedStart recording Pause/Resume recording28 EN Still Picture/Frame-By-FramePlayback On the VCR Slow Motion On the VCRSlow Motion On the Remote Variable Speed Search On the Remote30 EN Index SearchRepeat Playback Next Function MemoryAdjust the tracking manually Manual TrackingSoundtrack Selection Override automatic trackingVHS deck Record One Program While Watching Another Instant Timer Recording ITR32 EN Reset the counter Press C.RESET before starting recording or playbackElapsed Recording Time Indication Tape Remaining TimeSecond Audio Recording 34 ENRetake Recording Active Video CalibrationPlayback Press DV DV deckSelect the DV deck DV recording indicator lights on the VCR 38 EN Picture may appear distorted during variable speed searchVS30U1a-EN.fm Page 39 Thursday, January 31, 2002 335 PM 40 EN DV deck Record One Program While Watching Another Time CodeAccess the PlusCode No. screen Access the VCR Plus+ Program screenPrograming Select the deckCable Box or DBS Receiver Users Guide Channel Number SetAccess the Guide Channel Set screen 44 ENGuide Channel Number Set Enter the Guide Channel numberGuide Channel Number Enter the receiving channel position numberExpress Timer Access the PlusCode screenAccess the Program screen Enter the program start timeYou can program the timer while a regular recording is Timer ProgramingPerform Cable Box Control Setting on page 20 or DBS Anytime during steps 5 through 10, press WeeklyEnter the program mode Engage the VCR’s timer mode24HR Quick Programing 48 ENVS30U2-EN.fm Page 49 Thursday, January 31, 2002 338 PM 50 EN Check, cancel and change programsTo cancel or change a program START+/- , STOP+/- , DATE+/- , CH+/- , and/or SP/EP Select the program to modifyOverlap each other on the VHS deck Tape Dubbing 52 ENDubbing An Entire Cassette From DV to VHSFrom VHS to DV Dubbing An Entire Cassette Press DV, then press SP/LP p54 EN Locate the start point on the DV deckPrepare the VHS deck for dubbing Pause dubbingPrepare the DV deck for dubbing From VHS to DVLocate the start point on the VHS deck 56 EN Recorder PlayerSet the input mode of recording deck 58 ENStart the source player Start the recording deckConnection to a PC with DV connector Example When using this VCR as the source playerPC with DV connector Connection to another VCRAudio Dubbing 60 ENVHS Audio Dubbing DV Audio DubbingEngage the Audio Dubbing mode Make connections Start dubbingEnd Audio Dubbing Press A.DUBInsert Editing 62 ENVHS Insert Editing Source tape Recording tapeEngage the Insert Editing mode AV Insert Editing VHS deck onlyMake connections Start Editing Prepare the recording cassetteEditing 64 ENProgram Editing Memory Programs x 8 scenesLocate the end point Prepare the source tapeStart Random Assemble Editing End Random Assemble EditingRemote A/B Code Switching 66 ENChange the code for VCR To control two VCRs with the same RemoteSet the TV brand code Operate the TVBefore performing the following steps TV CH +/-,TV VOL+/-, TV Muting, number keysTV CH +/-,number keys 68 ENOperate the Cable Box Press Stop 8, and release POWER. The DBS ControlSet the DBS receiver brand code Operate the DBS receiverMode Set Access the Mode Set screenSelect the mode Select the mode settingMode SET When this function is set to onVHS Mode SET 72 ENVHS Mode SET 74 EN For ExampleCorrection to the luminance signal to enhance details Selecting either HI-FI L or HI-FI RNormally select this. Hi-Fi sound is played back Sound on the left Hi-Fi channel is played backDV Mode SET 76 ENPower 78 EN RecordingVHS deck DV deckTimer Recording 80 ENRecording Timer RecordingPlayback 82 EN Cable box Cable Box Control Setting Changing VCR Plus+ SettingExpress Timer Programming Timer Warning Display Tuner SetFebruary 23, 2002 606 pm
Related manuals
Manual 21 pages 16.45 Kb

SR-VS30U specifications

The JVC SR-VS30U is a versatile and high-performance digital video recorder designed to cater to both professionals and enthusiasts in the video production industry. This machine stands out due to its ability to blend two recording formats: DV (digital video) and S-VHS, making it a dual-format powerhouse suitable for various applications. One of its main features is the dual-deck capability, allowing users to record and play back S-VHS tapes while simultaneously digitizing video in the DV format. This flexibility makes it an excellent tool for archiving older videotape formats as well.

In terms of image quality, the JVC SR-VS30U boasts impressive specs. It supports S-VHS quality tapes that can deliver exceptional resolution, enhanced color reproduction, and fine detail, especially when paired with high-quality source material. The unit is equipped with advanced digital processing technologies that optimize video playback and recording, ensuring minimal signal degradation.

One of the key technologies integrated into the SR-VS30U is the built-in DV input and output interface. This allows for quick transfers of digital video to and from computer systems, making it convenient for video editing and processing tasks. The unit is also compliant with the IEEE 1394 FireWire standard, which is essential for facilitating seamless integration with modern editing software and digital devices.

The SR-VS30U features an easy-to-navigate user interface, complete with an LCD display that provides clear indications of recording status and tape position. The well-structured controls enhance usability, making it user-friendly for those both familiar and unfamiliar with video production equipment.

In terms of additional features, the unit comes with a range of editing functions, including insert and assemble edits, allowing for precise control over the final output. It also supports a variety of playback features, including various playback speeds and frame-by-frame options, which are instrumental in refining edits or analyzing footage.

The JVC SR-VS30U demonstrates a robust build quality, ensuring longevity for rigorous usage in professional environments. With these features and its dual-format capabilities, the SR-VS30U is an ideal choice for anyone looking to bridge the gap between traditional S-VHS media and modern digital workflows, providing a reliable and efficient solution for video recording and editing needs.
Top Page Image Contents