LG Electronics 37LD665H, 47LD555H, 42LD665H, 37LD555H, 32LD665H, 32LD555H Optional Set the Clock

Page 30

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.)

(Optional) Set the Clock

Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The TLL-1100A can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute.

Since the TLL-1100A’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port.

After the time is copied to the TLL-1100A clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV

1.Ensure the Target TV is in Pass-through Mode, and then use the Installer Remote to enter the Target TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6+ ENTER.

2.Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER. When the value changes back to 0, press ENTER again to exit the Installer Menu.

3.Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and then connect the MPI cable to the MPI port on the Target TV. The Clone Selection Menu will display on the TV screen.

4.Ensure the correct Memory CBank(X) is selected on the TLL-1100A.

5.Press 2 on the Installer Remote to select TEACH TO TV from the Clone Selection Menu. Then, press ENTER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on the screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

6.When Teaching is done, disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.

7.Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2)TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

-To change menu items, press channel keys or digits.

-To execute item, press Enter.

CLONE SELECTION MENU

Selected Bank: CBankX Saved

(1)LEARN FROM TV

(2) TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

THE CLONE IS VERSION VX.X.X

-To change menu items, press channel keys or digits.

-To execute item, press Enter.

30

206-4200

Image 30
Contents 206-4200 Rev B Copyright 2011, LG Electronics U.S.A., IncFor Customer Support/Service, please call­ Grounding Power CordOverloading Disconnect DeviceAntenna Grounding According to NEC, ANSI/NFPA CleaningOutdoor Antenna Grounding Transporting ProductTable of Contents Commercial Mode Overview Setup ChecklistPass-through Mode External MPI Control FTG ModeRemote Management in FTG Mode CloningProCentric TV Interactive Menu Features ProCentric OperationApplication Tuning Mode ProCentric SetupFTG Mode via CPU ProCentric Modes of OperationInstaller Remote Control Typical Key Functions EnterBefore You Begin Master TV SetupClonable TV Setup Menu Features Cloning MethodsMaster TV Setup Procedure Set Installer Menu itemsSet up TV features Channel Verify the TV setup Lock the channel lineupUsing the Installer Menu Installer MenuAccessing the Installer Menu Exiting the Installer Menu and Activating UpdatesInstaller Menu Items 000 through Brief Description of Function and CommentsInstaller Menu Items 075 through Rear RGB ENDetailed Descriptions of Installer Menu Items Installer SequenceFeature Level Mute DisableSleep Timer Caption LockAUX Status Back Lighting Atsc Tune ModeProcentric Atsc BandPower Savings Start Minor ChannelData Channel Channel Icons / Custom Text Labels 2-5-4 + Menu Mode To perform channel editing/labelingCloning Overview Before you begin cloningUSB Cloning Procedures Learn Setup from Master TVUSB Cloning Notes Teach Master TV Setup to Target TV Learn From TV TLL Teach To TV TLL Clone Programmer Cloning Procedures TLL-1100A Cloning NotesOptional Set the Clock LT2002 Cloning Notes LT2002 Clone ProgrammerFrom previous FTG Mode of Operation Overview FTG Mode via CPU or EBLFTG Mode via EBL Determining the TV Operating Mode TV Setup MenusFunction Menu FTG Mode via CPU From previous Teaching FTG Configuration to a TV Learning an FTG Configuration File from a TV Optional Manual Configuration / TV Setup Run Auto Tuning Channel SearchFTG Mode via EBL Local Configuration LD660H/LD665H Jack PanelLV555H Jack Panel FTG File Manager Main Screen FTG Configuration ListFTG File Manager Utilities Overview CLEAR/SAVEIP Channel Map FTG Channel Map Configuration UtilityRF Channel Map EDIT/ADD MAPADD UpdateFTG Channel Map Editor ExitFTG Installer Menu Configuration Utility Configuration SettingsNetwork Setup IP Environment SetupAccess the IP Environment Menu Offset SetupIP Environment Remote Jack Pack / TV Connections & Setup Remote Jack Pack SetupTV Connections Checking the Software Versions Upgrading TV/PTC SoftwareSplash Screen Image File Guidelines Downloading a Splash Screen ImageReference Power Consumption Settings 32/37/42LD660H & 32/37/42LD665H32/37/42/47/55LV555H 45.2 38%Camport Operation Pass-through Reference TV Camport Auto Sense OperationCamport Side Video Functionality Control Camport Operation FTG or PPVReference TV Aux Input Configuration Enable001 Default Off Reference b-LAN Setup & OverviewTV Standby State TV Power On State PowerReference RJP Model List and Input Auto-sensing Hierarchy RJP Model List Legacy Models Scaler ModelsRJP Input Auto-sensing Hierarchy Priority Video Audio Additional FTG Mode via CPU Options Reference Resetting Factory Defaults on the TVsInstaller Menu Item 117 Fact Default Additional FTG Mode via EBL OptionsReference TV Zone Restrictions EnterReference LD660H/LD665H Rear Jack Panel Reference LV555H Rear Jack Panel AntennaRGB in PC Audio in RGB/DVI Component LV555H TVs Reference Side Connections PanelLD660H/LD665H TVs 2 InputReference RF Antenna Connection LD660H/LD665H TVs onlyAntenna in Connect to Antenna/ Catv Troubleshooting General TroubleshootingTroubleshooting Flowchart Controller Quick CheckCommercial Mode Check / FTG Operation Troubleshooting FTG Operation TroubleshootingSymptom Possible Causes Solutions Clone Programmer Clone Programmer TroubleshootingSymptom Possible Causes Possible Solutions Master and Target TVsGlossary of Terms Document Revision History / Notes Document Revision HistoryDate Description For Customer Support/Service, please call­