Clone Programmer Cloning Procedures (Cont.)
Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer
Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.
Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).
LT2002 Cloning Notes
• Read the IMPORTANT CLONING |
INFORMATION on page 24 before |
beginning any cloning procedures. |
• A slow flashing green light indicates |
that there are communication |
Antenna |
or CATV |
MPI
Cable
| problems between the TV and the |
| LT2002. If this is the case, check for |
| a damaged cable, poor contacts, or |
| other connection troubles. |
• | If the status indicator is red, the |
| LT2002 batteries are low and should |
| be replaced. Install four (4) high- |
| quality alkaline AA batteries. |
• | Learning and Teaching is only |
| possible between identical model TVs; |
| however, the LT2002 can store up to |
| three different Master TV Setups. |
Learn Setup from Master TV
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION | XX | |
THE SW IS REVISION | XX | |
CLONE CLOCK = XX:XX |
| |
TV | CLOCK = XX:XX |
|
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
Ferrite Core (TDK, ZCAT
LT2002 Clone Programmer
Connect cable to |
|
|
|
|
|
| |
TV MPI Jack and |
| Status | |||||
follow on screen |
| ||||||
instructions |
| Indicator | |||||
| MPI |
|
|
|
| ||
|
|
|
|
|
|
| Reset |
|
|
|
| Color | |||
| • green |
| battery ok | ||||
| • red |
| battery low | ||||
|
|
| Blink pattern |
| |||
| • slow |
| power on | ||||
no communications
• heartbeat power on communications ok
QuickSet II Programmer
LT2002
ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA
1. Ensure the Master TV is set up completely and in
CLONE SELECTION MENU
2.Tune/set the TV to an analog channel or Aux input, and then plug one end of the MPI cable into the TV MPI port.
3.If there is a good connection after the LT2002 is connected to the TV MPI port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.
4.Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu.
5.Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press ENTER.
Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.
6.Verify the Learning setup information on the next screen, and then press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.
(Continued on next page)
(1) LEARN FROM TV
(2)TEACH TO TV
(3)SET CLONE CLOCK FROM TV
(4)SET TV CLOCK FROM CLONE
(5)DISPLAY TV SETUP
(6)DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.
SAVE TV SETUP IN SELECTED
CLONE MEMORY
(1)MEMORY 1 VER XX REV XX
(2)MEMORY 2 VER XX REV XX
(3)MEMORY 3 VER XX REV XX
(4)RETURN TO CLONE MENU
-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.
31 |