Peerless Industries PT660, PWS421 manual Tools Needed for Assembly, Table of Contents

Page 2

NOTE: Read entire instruction sheet before you start installation and assembly.

WARNING

Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact your local distributor.

This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

Never exceed the Maximum Load Capacity. See page one.

If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.

Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION

HARDWARE REQUIRED

Wood Stud

Included

Wood Beam

Included

Solid Concrete

Included

Cinder Block

Included

Metal Stud

Do not attach except with Peerless Metal Stud Accessory Kit - ACC415;

 

 

(not evaluated by UL)

Brick

Contact Qualified Professional (not evaluated by UL)

Other or unsure?

Contact Qualified Professional

Tools Needed for Assembly

stud finder ("edge to edge" stud finder is recommended)

phillips screwdriver

drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

level

Table of Contents

Parts List

3

Installation to Double Wood Stud Wall

4

Installation to Solid Concrete or Cinder Block

5

Installing Tilt Brackets

6

Mounting and Removing Flat Panel Screen

8

2 of 34

ISSUED: 02-05-09 SHEET #: 202-9272-4 04-12-10

Image 2
Contents Features Model PT660, PWS421/BKTools Needed for Assembly Table of ContentsParts List Installation to Double Wood Stud Wall Installation to Solid Concrete or Cinder Block Incorrect CorrectAttaching Tilt Brackets to Screen using Baffled Fastener Pack For Flat Back Screen Adjusting the Tilt Angle of the Flat Panel ScreenModelos PT660, PWS421/BK CaracterísticasEspañol Herramientas necesarias para el ensamblajeContenido Construcción DE LA Pared Accesorios NecesariosLista de piezas 11 deInstalación en una pared con montantes de madera dobles 12 de13 de Incorrecto Correcto14 de Instalación de los soportes inclinablesNotas 15 de 16 de Instalación y desinstalación de la pantalla planaAjustar el ángulo de inclinación de la pantalla Modèles PT660, PWS421/BK CaractéristiquesType DE MUR Pièces DE Fixation Requises Outils nécessaires au montageFrançais 18 surListe des pièces 19 surInstallation sur un mur à doubles montants en bois 20 surPlein 21 sur22 sur Installation des support inclinablesRemarques Pour les écrans à dos plat 23 sur24 sur Installation de l’écran plat sur la plaque muraleRéglage de l’inclinaison de l’écran plat Merkmale L USDeutsch Für den Zusammenbau erforderliche WerkzeugeInhaltsverzeichnis Wandkonstruktion Erforderliche BefestigungsteileTeileliste 27 vonInstallation zu verdoppeln Holzständerreihe Installation zu massivbeton oder porenbetonstein Falsch RichtigAchtung HinweiseBildschirme mit flacher Rückseite Abbildung Anbringung und Abnahme des FlachbildschirmsEinstellung des Neigungswinkels des Flachbildschirms Abbildund.4.1Limited FIVE-YEAR Warranty Garantie DE Cinq ANS
Related manuals
Manual 2 pages 47.8 Kb