Dish Network Solo 381 manual Controlling the TV’s Volume, Recover Button

Page 79

Remote Control Setup

Recover Button

Controlling the TV’s Volume

1Press TV for four seconds, and then let go of it. TV will blink.

2Press POUND (#).

3Press the plus (+) side of VOLUME.

4Press ZERO (0).

5Press POUND (#). TV flashes three times.

Now make sure the remote controls the TV’s volume:

6Press SAT.

7Press the plus (+) and minus (-) sides of VOLUME. The TV’s volume changes and TV lights instead of AUX.

RECOVER BUTTON

Use RECOVER if you accidentally change the channel or video input on your TV and cannot get the picture back from your satellite receiver. When you press RECOVER as described below, the remote control sends commands to your TV to change channels or video inputs to try to get you back to watching satellite programming. This procedure works only if you have accidentally changed the TV channel or video input. It does not recover lost satellite signal (See Troubleshooting on page 82 for information on solving problems).

Note: The remote must be programmed to control the TV (and VCR, if applicable) for RECOVER to work as described.

Note: RECOVER will first try to tune your TV to channel 3, then channel 4, and then other video inputs with each press of RECOVER. You may need to press RECOVER up to 30 times to recover your satellite TV video.

The following setup is required to use RECOVER:

The remote control must be set up to control the TV and, if installed, the VCR.

If a VCR is installed, make sure it is connected as shown on page 74.

55

Image 79
Contents Pay-Per-View Table of Contents Introduction Introduction to Dish Network ServicesWelcome WelcomeAbout Your Dish Network Account IntroductionWatching TV Now Where to Find Information on Your AccountPay-Per-View Additional ServicesSolar Interference Why Connect to a Phone LinePersonalizing Your Satellite Receiver Receiver CustomizationCaller ID Screens Setting Up Caller ID DisplayUsing Caller ID Using Caller IDChanging Languages Reset CC Defaults Using Dolby Surround SoundSelect Save Changing the Program Guide Order Resetting to Factory Defaults Questions TipsTips How to Connect Your Satellite Receiver Connections and SetupHigh-Definition TV Connections Connecting to a TVConnecting to a TV Standard-Definition TV ConnectionsYpbpr Connections Connections and SetupPage HD Display Connecting to Your Dish Antenna Connecting the Phone Line Phone System SetupPhone Line Connections Page Connecting OVER-THE-AIR ANTENNA/CABLE TV Setting Up the Receiver to Control Your VCRConnecting Over-the-Air Antenna/Cable TV Peaking Your Over-the-Air Antenna Scanning for Over-the-Air ChannelsTransmit Channel Numbers Display Options for Local ChannelsAbout Over-the-Air TV Broadcasts Chapter QAM Installations Resetting Your ReceiverPoint Dish and Check Switch DiagnosticsUsing Troubleshooting Tools About Your Satellite Receiver Receiver and Remote ControlPage Remote Control Chapter Receiver and Remote Control Satellite Receiver Front Panel Satellite Receiver Front Panel Satellite Receiver Back PanelOpen and Close Menus Using the MenusList of Choices in the Menus Using Text Fields Using the Virtual KeyboardWhy doesn’t my remote control work? Watching TV Finding Programs to WatchChanging Channels Changing ChannelsFinding Programs to Watch Using the Browse BannerUsing Search to Find a Program Finding a Program by its Theme Tips Order and Watch Pay-Per-Views Pay-Per-ViewBuying a Pay-Per-View Program Buying a PAY-PER-VIEW ProgramHow can I order an event for all my receivers? Questions Favorites Lists Setting Up Your Favorites ListsWhat are Favorites Lists? What are Favorites LISTS?Naming Favorites Lists Why are channels missing from the Program Guide?Questions Securing Your Receiver and Account LocksWhat are Locks? What are LOCKS?Locking and Unlocking Your Receiver Creating or Changing Channel Locks Locking or Unlocking PAY-PER-VIEW ChannelsHiding Adult Content Tips Interacting with Your TV Interactive TVCustomer Support DishHOME Setting Up and Using Timers TimersTimers Timer TypesTimer Frequency Timers ListWhen the Receiver is Off When a Timer Starts a RecordingSpecial Considerations When Using Timers Setting UP AN Automatic Timer Using the Timers List Setting UP a Quick RecordUsing the Timers List Setting Up a Manual Timer Overlapping Timers Personalizing Your Remote Control Remote Control SetupImproving Receiver Control Changing the AddressImproving Receiver Control Page Installing a UHF Attenuator Adjusting the Remote AntennaLimited Mode Remote Control ModesControlling Other Components Combination Devices Setting Up Using Device Code TablesRemote Control Setup Setting Up Using Device Codes ScanChapter Reading Out the Device Codes Controlling the Amplifier’s Volume Switching Between TV and Device Volume ControlNow make sure the remote controls the amplifier’s volume Recover Button Controlling the TV’s VolumeNow make sure the remote controls the TV’s volume Teaching Another Remote Control Remote Control Setup Sending Discrete Power On and Off Sending Discrete Power on and OFF107 Index 146733 Remote Control SettingsTV Input/Channel Settings Receiver InformationTroubleshooting Tables Remote Control Device Codes Troubleshooting and Device CodesTroubleshooting Tables Troubleshooting Tables003 Number Possible Reason What to Do001 002026 015018 022080 What Is Happening Possible Reason What to Do074 078Menus Remote ControlProgram Guide or the Browse Banner Favorites ListsWatching a Program Locks Caller IDTimer converts it to a manual TimersTelephone for Voice/Data/FAX Hearing a ProgramBuying a Pay-Per-View Program TV Codes Remote Control Device CodesVCR Codes Tuner/Amplifier Codes Reference Page Appendix Advance Exchange Program Residential Customer Agreement100 101 102 103 104 FCC Compliance FCC Compliance106