Programmed scan operation | Icom HF/VHF/UHF ALL MODE TRANSCEIVER

MEMORY AND SCAN OPERATION 5

■Programmed scan operation

➀Select VFO mode.

➁Select the desired operating mode.

•The operating mode can also be changed while scan- ning.

➂Set [SQL] open or closed.

•See page a left for squelch condition.

➃Select S2, then push [(F-1)SCN] to start the scan.

USB

S1 3 5 7 9	20 40	60dB	VFO A		Select
					VFO mode

PO	5	10		CH

S2 SCN PRI V/M

•Decimal point blinks while scanning.

➄When the scan detects a signal, the scan turns OFF, pauses or ignores it depending on the resume setting and the squelch condition.

•During scan [TS] can be used only when resume is ON.

➅To cancel the scan push [(F-1)SCN].

F-1	then push [(F-1)SCN]

Note: If the same frequencies are programmed into the scan edge memory channels 1A and 1B, pro- grammed scan does not start.

■Memory scan operation

➀Select memory mode.

➁Close the squelch with [SQL].

➂Select S2, then push [(F-1)SCN] to start the scan.

•Decimal point blinks while scanning.

➃When the scan detects a signal, the scan stops or pauses depending on the resume setting.

➄To cancel the scan push [(F-1)SCN].

USB

S1	3	5	7	9	20	40	60dB	Select
								memory mode
PO					5		10 MEMO CH

S2 SCN SEL V/M

F-1	then push [(F-1)SCN]

Note: Two or more memory channels must be pro- grammed for memory scan to start.

■Select memory scan operation

➀Select memory mode.

➁Close the squelch with [SQL].

➂Select S2, then push [(F-1)SCN] to start the mem-

ory scan.

•Decimal point blinks while scanning.

➃Push [(F-2)SEL] to change the memory scan to select memory scan.

•Push [(F-2)SEL] for 2 sec. to clear all select memory

			USB					Select
								memory mode
S1	3	5	7	9	20	40	60dB	Designate
							S
							S
PO				5			10 MEMO CH	“S.”
S2 SCN SEL V/M								“S.”
			F-1				F-2

	channels.	Push [(F-1)SCN], then [(F-2)SEL].
	➄When the scan detects a signal, the scan stops or	Note: Two or more memory channels must be desig-
	pauses depending on the resume setting.
		nated as select memory channels for select memory
	➅To cancel the scan push [(F-1)SCN].
		scan to start.

■Priority watch

➀Select VFO mode, then set a frequency.

➁Close the squelch with [SQL].

➂Set the desired memory channel as the watching

channel.

➃Select S2, then push [(F-2)PRI] to start the watch.

•Decimal point blinks while scanning.

➄When the scan detects a signal, the scan pauses for 10 sec. or until the signal disappears, depend- ing on the resume setting.

➅To cancel the scan push [(F-2)PRI].

USB

				Select
				VFO mode
S1 3 5 7 9	20 40	60dB	VFO A
PO	5	10	CH	Select watching
PO	5	10	CH

S2 SCN PRI V/M channel

F-2	Push [(F-2)PRI].

Note: The paused condition when detecting a signal differs depending on the scan resume condition. resume on: pauses for 10 sec.

resume off: pauses until the signal disappears.