Icom iC-706MKTMG, HF/VHF/UHF ALL MODE TRANSCEIVER manual Installation, DOperation

Page 64

10 OPTIONAL INSTALLATIONS/SETTINGS

■UT-106DSP RECEIVER UNIT

DInstallation

➀Open the transceiver case as shown on p. 59.

➁Remove the 4-pin connector (P251) from J1413 on the MAIN unit (top side) and plug it into J1 of the UT-106 on the PLL unit (bottom side).

➂Plug the 4-pin connector (P1) from the UT-106 into J1413 on the MAIN unit.

➃Plug the supplied ribbon cable into J3 on the UT- 106 and J253 on the PLL unit.

•Be careful of the orientation of the ribbon cable.

MAIN unit

P1

J1431

Remove the J1431 connector from the PLL unit and replace with the UT-106 connector

➄Attach the UT-106 to the PLL unit, using the exist- ing guide for alignment, as illustrated at right.

➅Reassemble the transceiver.

DOperation

Refer to the instructions supplied with the UT-106 for operating details.

Be careful of the orientation

UT-106when connecting the ribbon cable.

J3

J1

PLL unit

P251

P253

P1

unit position

■MB-72CARRYING HANDLE

The optional MB-72 CARRYING HANDLE is convenient when carrying the transceiver for DX’peditions, ﬁeld operation, etc.

➀Remove the 2 screws from the right side of the transceiver as shown below.

➁Replace those with 2 supplied screws plus rubber

rubber feet

feet and additionally attach 2 more supplied screws (including rubber feet) as shown below.

•When replacing the 2 screws at the rear, be sure to squeeze the top and bottom covers together to ensure proper alignment.

➂Attach the MB-72 to the left side of the transceiver as shown below.

carrying handle

61

Image 64

Contents I706MKG Precautions Word Definition RwarningTable of Contents Front panel Panel Description0MAIN Dial Tension Latch 2LOCK Switch Lock @2PREAMP/ATTENUATOR Switch P.AMP/ATTFunction switches VOX Function p Speech Compressor pBREAK-IN p Function pRear and side panels ACC PIN # Name Description Specifications Color When connecting the ACC conversion cable OPC-599ACC Socket 1DOT Matrix Indicators 3FUNCTION Indicators4DSP Indicators Function display➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock ➌PTT Switch PTTMicrophone Connector HM-103 Schematic DiagramInstallation and Connections PL-259 Connector Installation ExampleUnpacking GroundingInstallation Single body mountingStand Front panel separationRequired connections Rtty TerminalAdvanced connections Power supply connections Connecting the PS-85 DC Power SupplyConnecting a NON-ICOM DC Power Supply Connecting a NON-ICOMConnecting the AH-4 Connecting the AT-180Connecting the IC-PW1 External antenna tuners and linear ampliﬁerFrequency Setting When ﬁrst applying power CPU resettingInitial settings Power OFFVFO Mode Memory Mode pgsVFO description VFOFrequency setting Programmable tuning stepsHz and 10 Hz tuning steps Band selectionMHz quick tuning step TS Switch Flow ChartSSB/CW/RTTY modes Any mode FM/WFM/AM modes Sub dial functionMode selection Operating Mode SelectionQuick band change function ➁ Push F-1-F-3 to select a band stacking registerReceive and Transmit Functions for receiveIf shift function RIT functionNoise blanker AGC time constantPreamp and attenuator Peak meter holdSimple band scope RF gain and squelchRF/SQL control priority Filter Presetting Optional ﬁlter selectionFilter ON/OFF SSBANF Automatic Notch Filter function Ceiver maintains the ON/OFF condition when pushing F-2NRNR Noise Reduction function Functions for transmit Output power and mic gainDMeter function Speech compressor VOX operationOptional AT-180 Automatic Antenna Tuner operation Manual TuningTuner Operation ➂ The Tuner light lights constantly when tuning is complete Optional AH-4AUTOMATIC Antenna Tuner operationAH-4 operation PTT tune functionSplit frequency operation Quick split function➀ Select VFO a and set the frequency to 7.057 MHz/CW Split lock functionRepeater operation ➄ Push and hold PTT to transmit release PTT to receiveTone squelch operation Tone scan operation➅ Communicate in the usual manner ➂ Push F-3SCN to toggle tone scan operation on and OFFOne-touch repeater function Auto repeater functionThis function automatically activates the repeater set Frequency Duplex DirectionFunctions for CW Connections for CWCW operation Elec KEYCW reverse mode DElectronic CW keyer Quick SET ModeSetting the electronic keyer CW pitch controlConnections for Rtty FSK Functions for RttyConnections for Afsk Rtty FSK operation Presetting for RttyRtty Afsk operation Adjusting the transmit signal output from the TNC Packet operationConnections for packet Data socketSpot measurement Measuring SWRPlot measurement Memory and Scan Operation Memory channelsMemory channel selection Memory clearingProgramming in memory mode Programming in VFO modeMemory/call programming Frequency transferring Memory namesCalling up memory names Editing programming memory namesMemo pads Writing frequencies and operating modes into memo padsCalling up a frequency from a memo pad ➀ Select the S1 displayScan types PreparationProgrammed scan operation Memory scan operationSelect memory scan operation Priority watchCI-V connection example Remote Jack CI-V InformationData format Command Table VFO A=BSET Mode Quick set mode operationInitial set mode operation GeneralQuick set mode items Q3 VOX Delay SSB/AM/FM onlyQ2 MIC Gain SSB/AM/FM only Q4 VOX Gain SSB/AM/FM onlyQ5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL Quick Split quick split function Split Lock split lockSPL Offset split offset DUP HF duplex offsetAM NB Noise blanker in AM mode PWR on CHK Power on checkAuto Rptr auto repeater Scan Resume scan resume29 9600 Mode Data socket speed Tune Strt auto tuner startPTT Tune PTT tune function Vsend SEL ACC socket outputLVL Spch S-level speech CI-V Addres CI-V addressCI-V Baud CI-V data rate CI-V TRN CI-V transceiveMaintenance Fuse replacementMemory backup CleaningTroubleshooting Power Supply Receive Problem Possible Cause SolutionTransmit Display Scan Problem Possible Cause Solution Optional INSTALLATIONS/SETTINGS Opening the transceiver caseIf ﬁlters Installation DOperationS2 S1 B a AT-180 internal switch descriptionPIN no Description Name Top view Internal ViewsBottom view Options SP-7EXTERNAL Speaker SP-10EXTERNAL Speaker SP-12EXTERNAL SpeakerSP-20EXTERNAL Speaker SP-21EXTERNAL SpeakerSpecifications + power on Power OFF then on to exit initial set modeMenu Guide Indication Description No. IndicationSSB/AM/FM mode CW mode Rtty mode Mode DisplayFor 2 sec Menu DisplayCount on us