Icom iC-706MKTMG manual Installation and Connections, Unpacking, Grounding, Antenna

Page 12

2 INSTALLATION AND CONNECTIONS

■Unpacking

After unpacking, immediately report any damage to the delivering carrier or dealer. Keep the shipping car- tons.

■Grounding

To prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other prob- lems, ground the transceiver through the GROUND terminal on the rear panel.

For best results, connect a heavy gauge wire or strap to a long earth-sunk copper rod. Make the distance between the GROUND terminal and ground as short as possible.

For a description and a diagram of accessory equip- ment included with the IC-706MKIIG, see UNPACK- ING on p. ii of this manual.

RWARNING: NEVER connect the [GND] ter- minal to a gas or electric pipe, since the connection could cause an explosion or electric shock.

■Antenna

Select antenna(s), such as a well-matched 50 Ω antenna, and feedline. The transmission line should be a coaxial cable. 1.5 : 1 or better of Voltage Standing Wave Ratio (VSWR) is recommended for your required band. Of course, the transmission line should be a coaxial cable.

CAUTION: Protect your transceiver from lightning using a lightning arrestor.

ANTENNA SWR

Each antenna is tuned for a speciﬁed frequency range and SWR may be increased out-of-range. When the SWR is higher than approx. 2.0 : 1, the transceiver’s power drops to protect the ﬁnal transis- tors. In this case, an optional antenna tuner is useful to match the transceiver and antenna. Low SWR allows full power for transmitting even when using the antenna tuner. The IC-706MKIIG has an SWR meter to monitor the antenna SWR continuously.

PL-259 CONNECTOR INSTALLATION EXAMPLE

➀					30 mm





Coupling ring				10 mm (soft solder)
➁				10 mm			Soft
				10 mm

							solder



					1–2 mm

(10 mm ≈3⁄8 in)

Slide the coupling ring down. Strip the cable jacket and soft solder.

Strip the cable as shown at left. Soft solder the center con- ductor.

➂

➃

solder solder Slide the connector body on and solder it.

Screw the coupling ring onto the connector body.

9

Image 12

Contents I706MKG Precautions Word Definition RwarningTable of Contents Panel Description Front panel0MAIN Dial Tension Latch 2LOCK Switch Lock @2PREAMP/ATTENUATOR Switch P.AMP/ATTFunction switches VOX Function p Speech Compressor pBREAK-IN p Function pRear and side panels When connecting the ACC conversion cable OPC-599 ACC PIN # Name Description Specifications ColorACC Socket 1DOT Matrix Indicators 3FUNCTION Indicators4DSP Indicators Function display➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock ➌PTT Switch PTTMicrophone Connector HM-103 Schematic DiagramInstallation and Connections PL-259 Connector Installation ExampleUnpacking GroundingInstallation Single body mountingStand Front panel separationRequired connections Rtty TerminalAdvanced connections Power supply connections Connecting the PS-85 DC Power SupplyConnecting a NON-ICOM DC Power Supply Connecting a NON-ICOMConnecting the AH-4 Connecting the AT-180Connecting the IC-PW1 External antenna tuners and linear ampliﬁerFrequency Setting When ﬁrst applying power CPU resettingInitial settings Power OFFVFO Mode Memory Mode pgsVFO description VFOFrequency setting Programmable tuning stepsHz and 10 Hz tuning steps Band selectionMHz quick tuning step TS Switch Flow ChartSSB/CW/RTTY modes Any mode FM/WFM/AM modes Sub dial functionMode selection Operating Mode SelectionQuick band change function ➁ Push F-1-F-3 to select a band stacking registerReceive and Transmit Functions for receiveIf shift function RIT functionNoise blanker AGC time constantPreamp and attenuator Peak meter holdRF gain and squelch Simple band scopeRF/SQL control priority Filter Presetting Optional ﬁlter selectionFilter ON/OFF SSBCeiver maintains the ON/OFF condition when pushing F-2NR ANF Automatic Notch Filter functionNR Noise Reduction function Output power and mic gain Functions for transmitDMeter function Speech compressor VOX operationManual Tuning Optional AT-180 Automatic Antenna Tuner operationTuner Operation ➂ The Tuner light lights constantly when tuning is complete Optional AH-4AUTOMATIC Antenna Tuner operationAH-4 operation PTT tune functionSplit frequency operation Quick split function➀ Select VFO a and set the frequency to 7.057 MHz/CW Split lock functionRepeater operation ➄ Push and hold PTT to transmit release PTT to receiveTone squelch operation Tone scan operation➅ Communicate in the usual manner ➂ Push F-3SCN to toggle tone scan operation on and OFFOne-touch repeater function Auto repeater functionThis function automatically activates the repeater set Frequency Duplex DirectionFunctions for CW Connections for CWCW operation Elec KEYCW reverse mode DElectronic CW keyer Quick SET ModeSetting the electronic keyer CW pitch controlFunctions for Rtty Connections for Rtty FSKConnections for Afsk Presetting for Rtty Rtty FSK operationRtty Afsk operation Adjusting the transmit signal output from the TNC Packet operationConnections for packet Data socketMeasuring SWR Spot measurementPlot measurement Memory and Scan Operation Memory channelsMemory channel selection Memory clearingProgramming in VFO mode Programming in memory modeMemory/call programming Frequency transferring Memory namesCalling up memory names Editing programming memory namesMemo pads Writing frequencies and operating modes into memo padsCalling up a frequency from a memo pad ➀ Select the S1 displayScan types PreparationProgrammed scan operation Memory scan operationSelect memory scan operation Priority watchRemote Jack CI-V Information CI-V connection exampleData format Command Table VFO A=BSET Mode Quick set mode operationInitial set mode operation GeneralQuick set mode items Q3 VOX Delay SSB/AM/FM onlyQ2 MIC Gain SSB/AM/FM only Q4 VOX Gain SSB/AM/FM onlyQ5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL Quick Split quick split function Split Lock split lockSPL Offset split offset DUP HF duplex offsetAM NB Noise blanker in AM mode PWR on CHK Power on checkAuto Rptr auto repeater Scan Resume scan resume29 9600 Mode Data socket speed Tune Strt auto tuner startPTT Tune PTT tune function Vsend SEL ACC socket outputLVL Spch S-level speech CI-V Addres CI-V addressCI-V Baud CI-V data rate CI-V TRN CI-V transceiveMaintenance Fuse replacementMemory backup CleaningTroubleshooting Power Supply Receive Problem Possible Cause SolutionTransmit Display Scan Problem Possible Cause Solution Optional INSTALLATIONS/SETTINGS Opening the transceiver caseIf ﬁlters Installation DOperationAT-180 internal switch description S2 S1 B aPIN no Description Name Internal Views Top viewBottom view Options SP-7EXTERNAL Speaker SP-10EXTERNAL Speaker SP-12EXTERNAL SpeakerSP-20EXTERNAL Speaker SP-21EXTERNAL SpeakerSpecifications + power on Power OFF then on to exit initial set modeMenu Guide Indication Description No. IndicationSSB/AM/FM mode CW mode Rtty mode Mode DisplayFor 2 sec Menu DisplayCount on us