Icom iC-706MKTMG, HF/VHF/UHF ALL MODE TRANSCEIVER manual Rf/Sql Sql/Auto/Rfsql

Page 54

7 SET MODE

6AUTO OFF (auto power OFF)

The auto power OFF function can be used to auto- matically turn the transceiver OFF after a speciﬁed time of operation. This item can be set to 30 min., 60 min., 90 min., 120 min., or OFF.

Auto power OFF	Auto power OFF set to
deactivates. (default)	20 min.

7 RF/SQL (SQL/AUTO/RF•SQL)

The [RF/SQL] control can be set as the squelch con- trol (default), the RF/squelch control (USA version default) or automatic (acts as squelch in FM/WFM/AM modes; as RF in SSB/CW/RTTY modes). (See p. 22)

The [RF/SQL] control functions as RF gain control only.

The [RF/SQL] control functions as squelch control only.

8SUBDIAL (Subdial function)

When this item is set to “rit,” pushing [RIT/SUB] turns the RIT function ON (lights red)—rotating [M- CH] changes the RIT frequency; when this item is set to “Freq,” pushing [RIT/SUB] turns the sub dial func- tion ON (lights green)—rotating [M-CH] changes the operating frequency. Note that in FM, WFM and AM modes, pushing [RIT/SUB] always selects the sub dial function (lights green), regardless of this setting.

Pushing [RIT/SUB]	Pushing [RIT/SUB]
selects the RIT function	selects the sub dial function.
(default).

9 OPT. FIL 1 (optional ﬁlter)

When an optional ﬁlter is installed, this selection is necessary, otherwise the ﬁlters cannot be selected. Selections available are FL-100, FL-101, FL-103, FL- 223, FL-232 and none (default). See p. 22 for usable ﬁlters for each mode and see p. 60 for ﬁlter installa- tion.

No filters are selected	FL-223 (for LSB/USB mode)
(default).	is selected.

10 OPT. FIL 2 (optional ﬁlter)

When an optional ﬁlter is installed, this selection is necessary, otherwise the ﬁlters cannot be selected. Selections available are FL-100, FL-101, FL-103, FL- 223, FL-232 and none (default). See p. 22 for usable ﬁlters for each mode and see p. 60 for ﬁlter installa- tion.

No filters are selected	FL-223 (for LSB/USB mode)
(default).	is selected.

11PEAK HOLD (peak hold)

When the peak hold function is ON, the highest acti- vated segment of the meter remains visible for 0.5 sec.; when OFF, the meter functions normally.

Peak hold ON	Peak hold OFF
(default)

51

Image 54

Contents I706MKG Precautions Word Definition RwarningTable of Contents Panel Description Front panel0MAIN Dial Tension Latch 2LOCK Switch Lock @2PREAMP/ATTENUATOR Switch P.AMP/ATTFunction switches BREAK-IN p VOX Function pSpeech Compressor p Function pRear and side panels When connecting the ACC conversion cable OPC-599 ACC PIN # Name Description Specifications ColorACC Socket 4DSP Indicators 1DOT Matrix Indicators3FUNCTION Indicators Function displayMicrophone Connector ➊UP/DOWN Switches UP/DN ➋LOCK Switch Lock➌PTT Switch PTT HM-103 Schematic DiagramUnpacking Installation and ConnectionsPL-259 Connector Installation Example GroundingStand InstallationSingle body mounting Front panel separationRequired connections Rtty TerminalAdvanced connections Connecting a NON-ICOM DC Power Supply Power supply connectionsConnecting the PS-85 DC Power Supply Connecting a NON-ICOMConnecting the IC-PW1 Connecting the AH-4Connecting the AT-180 External antenna tuners and linear ampliﬁerInitial settings Frequency SettingWhen ﬁrst applying power CPU resetting Power OFFVFO description VFO ModeMemory Mode pgs VFOHz and 10 Hz tuning steps Frequency settingProgrammable tuning steps Band selectionSSB/CW/RTTY modes Any mode FM/WFM/AM modes MHz quick tuning stepTS Switch Flow Chart Sub dial functionQuick band change function Mode selectionOperating Mode Selection ➁ Push F-1-F-3 to select a band stacking registerIf shift function Receive and TransmitFunctions for receive RIT functionPreamp and attenuator Noise blankerAGC time constant Peak meter holdRF gain and squelch Simple band scopeRF/SQL control priority Filter ON/OFF Filter PresettingOptional ﬁlter selection SSBCeiver maintains the ON/OFF condition when pushing F-2NR ANF Automatic Notch Filter functionNR Noise Reduction function Output power and mic gain Functions for transmitDMeter function Speech compressor VOX operationManual Tuning Optional AT-180 Automatic Antenna Tuner operationTuner Operation AH-4 operation ➂ The Tuner light lights constantly when tuning is completeOptional AH-4AUTOMATIC Antenna Tuner operation PTT tune function➀ Select VFO a and set the frequency to 7.057 MHz/CW Split frequency operationQuick split function Split lock functionRepeater operation ➄ Push and hold PTT to transmit release PTT to receive➅ Communicate in the usual manner Tone squelch operationTone scan operation ➂ Push F-3SCN to toggle tone scan operation on and OFFThis function automatically activates the repeater set One-touch repeater functionAuto repeater function Frequency Duplex DirectionCW operation Functions for CWConnections for CW Elec KEYSetting the electronic keyer CW reverse modeDElectronic CW keyer Quick SET Mode CW pitch controlFunctions for Rtty Connections for Rtty FSKConnections for Afsk Presetting for Rtty Rtty FSK operationRtty Afsk operation Connections for packet Adjusting the transmit signal output from the TNCPacket operation Data socketMeasuring SWR Spot measurementPlot measurement Memory channel selection Memory and Scan OperationMemory channels Memory clearingProgramming in VFO mode Programming in memory modeMemory/call programming Calling up memory names Frequency transferringMemory names Editing programming memory namesCalling up a frequency from a memo pad Memo padsWriting frequencies and operating modes into memo pads ➀ Select the S1 displayScan types PreparationSelect memory scan operation Programmed scan operationMemory scan operation Priority watchRemote Jack CI-V Information CI-V connection exampleData format Command Table VFO A=BInitial set mode operation SET ModeQuick set mode operation GeneralQ2 MIC Gain SSB/AM/FM only Quick set mode itemsQ3 VOX Delay SSB/AM/FM only Q4 VOX Gain SSB/AM/FM onlyQ5 Anti VOX SSB/AM/FM only Initial set mode items RF/SQL SQL/AUTO/RFSQL SPL Offset split offset Quick Split quick split functionSplit Lock split lock DUP HF duplex offsetAuto Rptr auto repeater AM NB Noise blanker in AM modePWR on CHK Power on check Scan Resume scan resumePTT Tune PTT tune function 29 9600 Mode Data socket speedTune Strt auto tuner start Vsend SEL ACC socket outputCI-V Baud CI-V data rate LVL Spch S-level speechCI-V Addres CI-V address CI-V TRN CI-V transceiveMemory backup MaintenanceFuse replacement CleaningTroubleshooting Power Supply Receive Problem Possible Cause SolutionTransmit Display Scan Problem Possible Cause Solution Optional INSTALLATIONS/SETTINGS Opening the transceiver caseIf ﬁlters Installation DOperationAT-180 internal switch description S2 S1 B aPIN no Description Name Internal Views Top viewBottom view Options SP-20EXTERNAL Speaker SP-7EXTERNAL SpeakerSP-10EXTERNAL Speaker SP-12EXTERNAL Speaker SP-21EXTERNAL SpeakerSpecifications Menu Guide + power onPower OFF then on to exit initial set mode Indication Description No. IndicationFor 2 sec SSB/AM/FM mode CW mode Rtty modeMode Display Menu DisplayCount on us