Symphonic CSC313E owner manual To Change Clock Setting, Automatic Clock Setting, Press F.FWD/ B

08 10 13

6 Select the hour	– MANUAL CLOCK SET –
Press [PLAY/K] or [STOP/L]	MONTH DAY			YEAR
until your desired hour appears.	0 5	/ 0 5	THU	2 0 0 5
(Example: “5”, “PM”)	HOUR	MINUTE
Then press [F.FWD/ B].	0 5	: – –	PM
7 Select the minute	– MANUAL CLOCK SET –
Press [PLAY/K] or [STOP/L]	MONTH DAY			YEAR
until the desired minute appears.	0 5	/ 0 5	THU	2 0 0 5
(Example: “40”)	HOUR	MINUTE
	0 5	: 4 0	PM

8 Start the clock

Press [MENU].

5:40 PM

Although seconds are not dis- played, they begin counting from 00 when you press [MENU]. Use this feature to synchronize the clock with the correct time.

NOTE:

•When unplugging the AC cord or if there is a power failure for more than 3 seconds, you may have to reset the clock.

TO CHANGE CLOCK SETTING

If you want to change the clock, 1)Follow steps 1 to 2 on page 13.

2)Select the item you want to change using [REW/s] or [F.FWD/ B].

3)Enter correct numbers using [PLAY/K] or [STOP/L].

1 Select “SETTING CLOCK”	– M E N U –
Press [MENU].	TIMER PROGRAMMING
	PICTURE CONTROL
Press [PLAY/K] or [STOP/L] to	B SETTING CLOCK
	CHANNEL SET UP
	USER’S SET UP
select “SETTING CLOCK”, then	V-CHIP SET UP
	LANGUAGE [ENGLISH]
	CAPTION [OFF]
press [F.FWD/ B].	ZERO RETURN
	TIME SEARCH
2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –
Press [F.FWD/ B] until “AUTO	B AUTO CLOCK	[ON]
	AUTO CLOCK CH SEARCH
CLOCK [ON]” appears.
	AUTO CLOCK CH	[ 02 ]
	MANUAL CLOCK SET
	D.S.T.	[OFF]

3Begin “AUTO CLOCK CH SEARCH”

Press [STOP/L] to select “AUTO	– SETTING CLOCK –
CLOCK CH SEARCH”.	AUTO CLOCK	[ON]
	B AUTO CLOCK CH SEARCH
Then press [F.FWD/ B].
	AUTO CLOCK CH	[ 02 ]
• The unit begins searching for the	MANUAL CLOCK SET
station which contains the auto	D.S.T.	[OFF]

clock set signal. The search for a

signal may take up to 20 seconds per channel.

•When the search has ended, “_ _” – AUTO CLOCK CH SEARCH –

appears at the lower left of the screen.

• Write down the number(s) that	_ _
appear on the screen. They are
the auto clock station(s) in your
area.

•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 13. Press [MENU] to exit the screen.

4)Press [MENU] to start the clock.

NOTE:

•If there is no local PBS station in your area or on your cable system, select “AUTO CLOCK” and press [REW/s] or [F.FWD/ B] to turn [OFF] this function. Then you can manually adjust the clock.

AUTOMATIC CLOCK SETTING

Make sure ...

NOTE:

•During AUTO CLOCK CH SEARCH, the picture may be distorted.

4Enter the channel number that contains the Automatic Clock Setting Signal

Follow step 1 above to select “SETTING CLOCK” menu.

•The unit must be turned on.

•Confirm the unit is receiving a RF (Radio Frequency) signal from either an antenna or cable system connection using the ANT. jack on the rear of the unit.

NOTES:

• If a cable converter box is being used, make sure it

is powered on.

• You must use the remote control to perform the

Press [STOP/L] to select “AUTO CLOCK CH”.

Press [REW/s] or [F.FWD/ B] until you locate Auto Clock Set station number that you wrote down at step 3.

Press [MENU] to exit the screen.

– SETTING CLOCK –

AUTO CLOCK	[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH	[ 45 ]
MANUAL CLOCK SET
D.S.T.	[OFF]

clock setting procedure.

• If the unit is connected directly to a cable converter

box or satellite box, the local PBS station must be

selected on the cable box itself and the unit must

be set to the output channel of the cable converter

box or satellite box (usually channel 3 or 4), to be

able to set up or correct the clock automatically.

5Turn off the unit

Once the unit is turned off, it will periodically check and set the correct date and time.

- 14 - EN