Toshiba RD-XS52SU, RD-XS52SC, RD-KX50SU owner manual Audio setting for the Hdmi connection

Page 27

Set the output resolution for the HDMI output that best matches your TV’s capabilities

Set an output signal from the HDMI terminal of the recorder in accordance with your TV’s input signal.

				Pressing PROG/HDMI button on the front panel or the
				remote control changes output signals as below. See
				the HDMI indicator and select the appropriate output
				signal.
ON / STANDBY	CH	INPUT SELECT REC MODE	DIMMER PROG/HDMI		HDMI indicator		Video output signal
				Press	illuminates “	1080i”	1080i (interlace)
					illuminates “	1080i”	1080i (interlace)
PROG/HDMI button			HDMI indicator			Press
						Press

illuminates “ 720p”

720p (progressive)

PROG/HDMI

Press

Front panel

illuminates “ 480p”

480p (progressive)

Remote control	PROG/HDMI	Press

off	480i (interlace)

480p, 720p and 1080i are signals created with this recorder from original 480i signal. The resolution of the picture may not be increased even if they are selected.

Note

•PROG/HDMI button is not available during the operations below.

- All HDD title delete	- TIME SLIP (Pause TV/Chase Play)
- HDD format	- Rate conversion dubbing (Only when copying is in progress.)
- DVD-RAM physical format	- DVD-Video creation (EDIT MENU)
- DVD format	(Only when copying is in progress.)

(PROG/HDMI button may not be available during some other operations either.)

Introduction

Connections

Basic Setup

Audio setting for the HDMI connection

The HDMI connection will only output “PCM”.

Set “Audio out select” of “Picture/Audio setting” to “PCM” ( page 48).

Note

•When the HDMI connection is used, “Black level”, “Custom picture select” and “Custom picture setting” of “Picture/Audio settings” are not available.

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

27

Image 27

Contents RD-XS52SU RD-XS52SC RD-KX50SU See service procedure This HDD/DVD video recorder employs a Laser SystemMay result in hazardous radiation exposure Location of the required label Important Safety Instructions Additional Safety Instructions Precautions When not in useIntroduction Exemptions Power OutageMoisture condensation occurs during the following cases Introduction PrecautionsDo not use the unit when moisture condensation may occur WaitConnections Registration card Installation procedureAccessories Remote control Batteries AAA x Video/Audio cable IR control cableAbout this product DVD-RAM discs for your personal library Using different disc types for different purposesFor recording / playback Disc Mark Specification Remarks Choosing a discDisc For playback only Disc Mark Specification RemarksDVD-RAM discs with cartridges are recommended for recording To protect recorded contentsOn DVD-RAM discs Introduction Choosing a discMarks on DVD video discs On DVD-R discsOn storing discs Structure of disc contentsOn cleaning discs On handling discsTable of Contents Close the cover Preparation of the remote controlOperating with the remote control Open the cover Insert batteries AAA sizeConnection procedure When you connect a TV equipped with audio/ video inputsWhen you connect an audio system Connections Connecting an antenna and TVConnect to a TV equiped with audio/video inputs Connect the power cord of the recorder to a wall outletConnecting to cable TV signal This set-up will allow you toYou will need to Component Output When the satellite system has audio/video outputs Connecting to a satellite systemConnecting the IR control cable Signal sensor of the set top boxTransmitter About Hdmitm Connecting to a TV with the Hdmi terminalAudio setting for the Hdmi connection Component video outputs/inputs Connecting to aTV equipped with component video inputsDigital audio input Connecting to an audio systemPage Basic Setup Turning the power off Basic SetupTurning the power on ON/STANDBY button ON/STANDBY indicatorStartup/finishing closing icons Press Setup Initial settingsFunction Tip on settingIf a message appears Example of the iconLanguage setting Basic Setup Initial settingsPress / to select a language, then press Auto Time and date settingAuto clock setting Press / to select Auto or Manual, then press EnterNo Use Press EnterAuto UsePress / to select Yes, then press Enter Manual clock settingPress / and Adjust / to set the clock After setting all the items, press EnterChannel setting Press / to select Channel setting, then press EnterPress / to select TV or Cable, then press Enter Channel reference Press / to select Auto, then pressAdding or erasing channels Preparation Set top box settingPress , then press Adjust or / to select Off or On PressOff 10Press Setup RCA Set top box brand codeSample of a Guide channel chart from a local TV listing Guide channel settingGuide channel number 33 HBO Press / to select Audio out select, then press Enter Output sound settingPress Setup to display the setup menu Press / to select Picture/Audio settings, then press EnterAnalog 2ch Once the proper setting is selected, pressPress / to select the output sound format BitstreamTV shape setting Press / to select Display settings, then press EnterPress / to select TV shape, then press Press / to select the picture shape When the proper setting is selected, pressRelease TV Code Remote control settingsOperating a TV with the remote control of this recorder Operating your TV with the remote controlJVC Brand code tablePress / to select DR 2 example, then press Enter Setting up the recorder Press SetupPress / to select Operational settings, then press Enter Press / to select IR code, then pressDisabling the remote control for a temporary period Commercial Units Limited Ninety 90 Day Warranty on LaborLimited One 1 Year Warranty on Parts Rental UnitsHow to Obtain Warranty Services Canadian Warranty Information Garantie Canadienne Memo Printed on 70% Recycled Paper