Toshiba kV-9960A instruction manual Connecting the Alarm Terminals

Page 31

Connecting the Alarm Terminals

iConnecting the ALARM IN/OUT terminals

Alarm switch

To alarm in

To GND




Warning		External
Warning		interface

				To alarm out
				To alarm out
	Alarm lamp or alarm buzzer

•When the alarm switch is ON, alarm recording starts. It is possible to confirm the warning from outside by connecting the switching input of external interface devices such as alarm lamp or alarm buzzer to the alarm output. Please do not use the alarm output for power source to any of external devices.

i Connecting alarm reset input

Alarm reset switch

To GND

To alarm reset

•When the alarm switch is ON, alarm recording starts. However, when a closure is applied across the ALARM RESET and GND terminals, the alarm record condition resets and the VCR returns to the original record mode it was in before the alarm condition occurred.

Note:

iWhen simultaneously connecting alarm input and alarm reset input, be sure to carefully check the voltage levels.

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

30

Image 31

Contents Instruction Manual Please Read Important PrecautionsUnplug this product from the wall Important Safety InstructionsPower Sources Radiators, heat registers, stovesTo restore the product to its normal operation AccessoriesPower Lines When the power-supply cord or plug is damagedTable of Contents FeaturesFront Panel Instructions in BriefDisplay button Time Mode / SET + buttonsTape Remain button Cassette CompartmentRear Panel Removal Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery InstallationVCR Display Press to start play back REW buttonFF button Connection with a Video Camera ConnectionsOutput Typical Connection with the Sequential SwitcherVideo To REC TRIGG. OUTContents of Screen Display Alarm Recall Screen Operation Setting the ClockMonitor screen ON-SCREEN FunctionsDate-Time Display VCR displayDisplay Screen This function enables to indicate and record information Alarm numberIs pressed. When an alarm is Changes to the alarm numberCounter Memory Alarm MemoryWhen the tape reaches Counter DisplaysCode Number Condition of Abnormality Error MessageRegarding the error code E-6 Display Tape RemainHOW to Operate 24 Hour Virtual Real Time Mode Setting the RECORDING/PLAY Back TimeMode display Loading a Cassette Loading and Unloading a Video CassetteUnloading a Cassette Camera and monitor TV Not been removed RecordingRestart Recording Setting the Restart RecordingProgram Screen Timer RecordingSetting the Timer Program Daily Timer RecordingDuring timer power off mode, alarm recording will not Time Mode button is pressed, the displayPress the Timer button Should be more than 1 minute. If they are same, timerPress the Shift ButtonGRAM.to blink PRO Weekly Timer RecordingPress the Shift Button to blink the MO1 start time DLY Overlapping ProgramsExample FR2Event Recording Alarm RecordingOperation at Alarm Input Alarm Recall DisplayConnecting the Alarm Terminals Manual Setting the Alarm RecordingDisplay Recording time ContAuto recording Connecting the External control terminalAuto Recording Operation of Auto RecordingPress the + or SET How to Release Auto RecordingHow to Forbid Auto Recording Press Timer button to release the timer modeDisplay Operation after detection of tape end How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Operation After Tape END DetectionAlarm recording does not operate during auto-rewind How to Set to Auto Rewind at End of TapeMenu Screen ButtonREC. to select REW → How to Set to Repeat Record at End of TapeC D a B C D Recording with the Sequential SwitcherConnection with the Sequential Switcher Timing for Camera SwitchingTrigger SEL REC Trigger Output Selection in the Alarm RecordingPress the Shift Button to set the RECRecording time mode Time mode for playback Tracking AdjustmentPlayback Slow Still Play Using the Shuttle DialREW Stop Picture Search PlayPlayback in Various Modes Search Operation Time Date SearchPress the SET button to Set the Minute to Alarm M to light Alarm SearchStill picture mode Press the Play button Input/Output terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsOrder of Daily Checks Check the playback picture recorded in SPA2 modePress the or Time Mode button to go to SPA2 mode Daily and Periodic InspectionRequest for Periodic Checks Steps to Take after Daily ChecksTape Usage Frequency Dew Condensation Recording Before Calling Service PersonnelInstallation Function/OperationOther matters PlaybackDew caution sheet SpecificationsConnector section Accessories70971826 Limited Warranty