Toshiba kV-9960A Word on the Exclusive 3N-100AAS Battery Pack, Specification of Battery, Removal

Page 9

A Word on the Exclusive 3N-100AAS Battery Pack

The nickel-cadmium battery pack (3N-100AAS) is used for power source of the built-in clock and memory circuit.

Charging the Battery Pack

1.Turn on the power of the VCR.

2.The battery pack in the VCR is charged.

Battery Installation

Removal:

1.Remove the battery cover.

2.Disconnect the connector in the VCR.

RED wire

Connector

Battery pack

Installation:

1.Install the battery pack placing the red wire upside, and connect the connector on the battery pack to this VCR. Make sure the polarities (+) and (–) are correct.

2.Close the battery cover.

Note:

If the Battery Pack is removed, the memory data will be erased. In such a case, perform the setting from the first step.

Specification of Battery

i

Temperature

 

 

 

For charging

:

0°C to 80°C

 

For operating

:

–20°C to 80°C

 

For storing

:

–30°C to 80°C

i

Charging time

:

more than 48 hours

Notes:

iUse only for this VCR.

iDo not dispose of the batteries into fire.

iDo not short circuit the terminals.

iDo not modify or disassemble.

iAvoid dropping, unnecessary shocks.

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

8

Image 9
Contents Instruction Manual Please Read Important PrecautionsPower Sources Important Safety InstructionsRadiators, heat registers, stoves Unplug this product from the wallPower Lines AccessoriesWhen the power-supply cord or plug is damaged To restore the product to its normal operationTable of Contents FeaturesFront Panel Instructions in BriefTape Remain button Time Mode / SET + buttonsCassette Compartment Display buttonRear Panel Specification of Battery Word on the Exclusive 3N-100AAS Battery PackInstallation RemovalVCR Display REW button Press to start play backFF button Connection with a Video Camera ConnectionsVideo Typical Connection with the Sequential SwitcherTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Operation Setting the ClockDate-Time Display ON-SCREEN FunctionsVCR display Monitor screenDisplay Screen Is pressed. When an alarm is Alarm numberChanges to the alarm number This function enables to indicate and record informationWhen the tape reaches Alarm MemoryCounter Displays Counter MemoryRegarding the error code E-6 Display Error MessageTape Remain Code Number Condition of AbnormalitySetting the RECORDING/PLAY Back Time HOW to Operate 24 Hour Virtual Real Time ModeMode display Loading and Unloading a Video Cassette Loading a CassetteUnloading a Cassette Camera and monitor TV Not been removed RecordingRestart Recording Setting the Restart RecordingSetting the Timer Program Timer RecordingDaily Timer Recording Program ScreenPress the Timer button Time Mode button is pressed, the displayShould be more than 1 minute. If they are same, timer During timer power off mode, alarm recording will notWeekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time Example Overlapping ProgramsFR2 DLYOperation at Alarm Input Alarm RecordingAlarm Recall Display Event RecordingConnecting the Alarm Terminals Display Recording time Setting the Alarm RecordingCont ManualAuto Recording Connecting the External control terminalOperation of Auto Recording Auto recordingHow to Forbid Auto Recording How to Release Auto RecordingPress Timer button to release the timer mode Press the + or SETSetting contents Buzzer Screen display Counter display How to Set to Stop at End of TapeOperation After Tape END Detection Display Operation after detection of tape endHow to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindMenu Screen ButtonREC. to select REW → How to Set to Repeat Record at End of TapeConnection with the Sequential Switcher Recording with the Sequential SwitcherTiming for Camera Switching C D a B C DPress the Shift REC Trigger Output Selection in the Alarm RecordingButton to set the REC Trigger SELTracking Adjustment Recording time mode Time mode for playbackPlayback REW Stop Using the Shuttle DialPicture Search Play Slow Still PlayPlayback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Alarm Search Alarm M to lightStill picture mode Press the Play button Input/Output terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT TerminalsPress the or Time Mode button to go to SPA2 mode Check the playback picture recorded in SPA2 modeDaily and Periodic Inspection Order of Daily ChecksSteps to Take after Daily Checks Request for Periodic ChecksTape Usage Frequency Dew Condensation Installation Before Calling Service PersonnelFunction/Operation RecordingOther matters PlaybackConnector section SpecificationsAccessories Dew caution sheet70971826 Limited Warranty