Toshiba kV-9960A instruction manual Rear Panel

Page 8

INTRODUCTION

Rear Panel

PREPARATION

OPTION BOX cover

4

5

6

 

 

ALL CLEAR

 

 

 

 

IN

GND

ALARM

RESET

 

 

 

OUT

 

GND

.

EXT CONT

IN

 

 

 

GND

.

REC TRIGG

OUT

 

TAPE END

SEE MANUAL

3

13

1

2

7

9

10 BATTERY cover

REMOTE IN

MIC IN

IN VIDEO OUT

AUDIO

SEE MANUAL

8 11 12

RECORDING

OPERATION

 

 

PLAYBACK

OPERATION

 

 

1TAPE END OUT terminal

Signal output terminal to annunciate to other devices that the tape has run out on the VCR.

2REC TRIGGER OUT terminal

Signal output terminal to control the switching interval of the video cameras when connected to a sequential switcher or multiplexer.

3ALARM OUT terminal

Output terminal to transmit an alarm signal to peripheral equipment.

4ALARM RESET terminal

Input terminal to reset alarm recording.

Alarm recording is reset when this terminal is connected to the ground terminal during recording.

5ALARM IN terminal

Input terminal to start alarm recording.

The VCR goes into alarm recording mode when this terminal is connected to the ground terminal while in the record mode, record pause mode, or stop mode.

6ALL CLEAR button

Pressing this button will clear the entire time-date, and timer program memory. The power will be turned off at the same time. Pressing the POWER button will restore power.

pVIDEO OUT connector (BNC)

Output connector for video signal. Connect with a monitor TV.

qAUDIO IN jack (RCA type)

Input jack for audio signal. Connect with an external audio source.

wAUDIO OUT jack (RCA type)

Output jack for audio signal. Connect with an external audio equipment.

eEXTERNAL CONTROL IN terminal

Automatic recording is performed when this terminal is connected to the signal ground while in the timer mode (timer recording or timer standby).

Notes:

•ALL CLEAR button

Do not use this function (ALL CLEAR) frequently. Press this button only when an abnormality (ex. VCR display does not turn ON.) occurs.

When this button is pressed, the power turns OFF and each data stored (ex. clock, timer program, etc.) is cleared and returns to the initial setting status. It will be necessary to re-program the VCR after turning the unit on again.

NOTICE

7REMOTE IN jack

Input jack for optional wired remote control.

8MIC IN jack

Input jack for audio signals from a microphone. The RCA jack input (audio input) is automatically switched off when this jack is utilized.

9VIDEO IN connector (BNC)

Input connector for video signal. Connect with an external video source such as a video camera, etc.

•OPTION BOX cover

This VCR provides an optional port for connecting an optional module to the rear of the unit.

If you would like additional information regarding the available options for this VCR please consult your dealer. The installation of the optional module should be per- formed only by qualified technical personnel.

7

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Instruction Manual Important Precautions Please ReadImportant Safety Instructions Power SourcesRadiators, heat registers, stoves Unplug this product from the wallAccessories Power LinesWhen the power-supply cord or plug is damaged To restore the product to its normal operationFeatures Table of ContentsInstructions in Brief Front PanelTime Mode / SET + buttons Tape Remain buttonCassette Compartment Display buttonRear Panel Word on the Exclusive 3N-100AAS Battery Pack Specification of BatteryInstallation RemovalVCR Display FF button REW buttonPress to start play back Connections Connection with a Video CameraTypical Connection with the Sequential Switcher VideoTo REC TRIGG. OUT OutputContents of Screen Display Alarm Recall Screen Setting the Clock OperationON-SCREEN Functions Date-Time DisplayVCR display Monitor screenDisplay Screen Alarm number Is pressed. When an alarm isChanges to the alarm number This function enables to indicate and record informationAlarm Memory When the tape reachesCounter Displays Counter MemoryError Message Regarding the error code E-6 DisplayTape Remain Code Number Condition of AbnormalityMode display Setting the RECORDING/PLAY Back TimeHOW to Operate 24 Hour Virtual Real Time Mode Unloading a Cassette Loading and Unloading a Video CassetteLoading a Cassette Recording Camera and monitor TV Not been removedSetting the Restart Recording Restart RecordingTimer Recording Setting the Timer ProgramDaily Timer Recording Program ScreenTime Mode button is pressed, the display Press the Timer buttonShould be more than 1 minute. If they are same, timer During timer power off mode, alarm recording will notPress the Shift Button to blink the MO1 start time Weekly Timer RecordingPress the Shift ButtonGRAM.to blink PRO Overlapping Programs ExampleFR2 DLYAlarm Recording Operation at Alarm InputAlarm Recall Display Event RecordingConnecting the Alarm Terminals Setting the Alarm Recording Display Recording timeCont ManualConnecting the External control terminal Auto RecordingOperation of Auto Recording Auto recordingHow to Release Auto Recording How to Forbid Auto RecordingPress Timer button to release the timer mode Press the + or SETHow to Set to Stop at End of Tape Setting contents Buzzer Screen display Counter displayOperation After Tape END Detection Display Operation after detection of tape endMenu Screen How to Set to Auto Rewind at End of TapeAlarm recording does not operate during auto-rewind How to Set to Repeat Record at End of Tape ButtonREC. to select REW →Recording with the Sequential Switcher Connection with the Sequential SwitcherTiming for Camera Switching C D a B C DREC Trigger Output Selection in the Alarm Recording Press the ShiftButton to set the REC Trigger SELPlayback Tracking AdjustmentRecording time mode Time mode for playback Using the Shuttle Dial REW StopPicture Search Play Slow Still PlayPlayback in Various Modes Press the SET button to Set the Minute to Time Date SearchSearch Operation Still picture mode Press the Play button Alarm SearchAlarm M to light Signal Levels of INPUT/OUTPUT Terminals Input/Output terminal Signal level Additional remarksCheck the playback picture recorded in SPA2 mode Press the or Time Mode button to go to SPA2 modeDaily and Periodic Inspection Order of Daily ChecksTape Usage Frequency Steps to Take after Daily ChecksRequest for Periodic Checks Dew Condensation Before Calling Service Personnel InstallationFunction/Operation RecordingPlayback Other mattersSpecifications Connector sectionAccessories Dew caution sheetLimited Warranty 70971826
Top Page Image Contents