GE DVMRe user manual Camera Inputs, Composite Monitor Output, Alarm I/O Port

Page 11

Camera Inputs

There are two BNC jacks for each camera. Either jack can receive a camera signal. The signal is looped (directly connected to the other jack), making the camera signal available to other equipment.

The camera input connectors are Auto Terminating.

Cable: 75-Ohm Coaxial

Connectors: BNC

Auto Terminating: Yes

Passive Looping: Yes

This means that the input signal will automatically be terminated with 75-Ohms unless a 2nd cable is connected to the 2nd BNC connector of the same camera input. Make sure there is 75-Ohm termination at the end of the video line if the signal is looped through the DVMRe Triplex.

Time base correction is performed during digital capture. As a result, cameras do not require synchronization.

See section 3.14 for information about disabling unused camera jacks in the menu system.

Composite Monitor Output

When connecting directly from the DVMRe Triplex to the monitor, select the 75-Ohm impedance setting on the monitor.

Cable: 75-Ohm Coaxial

Connectors: BNC

If an additional device is connected to the monitor’s looping output, set the termination of the additional device as 75-Ohm, and set the termination of the monitor as Hi-Z (High Impedance).

Y/C Monitor Output

Y/C video output has a 4-pin mini-DIN style connector. This style of connection is also referred to as SVHS and S-Video.

Cable: 75-Ohm Coaxial

Connectors: BNC

Alarm I/O Port

The back panel of the unit is equipped with an Alarm

Port (DB-25 style connector).

Do not attempt to wire directly to the DB-25	DB-25 Connector on Back Panel
connector on the back panel.

Connect the Alarm PCB (supplied with the unit) to the Alarm Port. Wire all alarm inputs to the Alarm PCB per the pin out specifications shown below.

0150-0193F

11

Kalatel DVMRe Triplex

Image 11

Contents Kalatel DVMRe Triplex Page Important Information Contents WebBrowser AlarmsRS232 Remote Control Protocol Searching11.2 11Warranty and Service10.2 Scheduled Macro Table 11.1Product Description Products Featured In This ManualFeatures DVMRe Triplex OverviewDefault Passwords Four-Channel Units PasswordsTen and Sixteen-Channel Units Installation EnvironmentPackage Contents UnpackingBack Panel Associated EquipmentMonitor Output Alarm I/O PortCamera Inputs Composite Monitor OutputNormally Open and Normally Closed Connections Alarm InputAlarm PCB Voltage 30V Max Alarm Relay OutputExternal Alarm Acknowledge Input AUX PortEthernet Port RS485 ConnectorRJ-45 Pin Configuration For RS485 Port Gender on unit Female RJ-45 Pin Configuration For Ethernet PortIeee 1394 Firewire Port Scsi PortPower-Up Check Record And Playback Quality Minimum Recommended Menu SetupQuickInstall Main Menu Location Section Menu Item Manual Play Forward Button Begins Playback DMVRe Triplex Basic OperationsPrincipal Operating Modes Front PanelLive Viewing Playback Sequence Button Number Button Stop PlaybackSearching Recorded Data Stop ButtonRecord Button RecordingMonitor Displays During Recording Available Multiscreen Displays Entering Active Cameo ModeDisplay Options Active CameosDwell Time Returning To The Default Sequence ListSequencing Selecting CamerasSequencing In Cameos On-screen IndicatorsChanging Position And Color Of Title And Status Indicators Status IndicatorsATM/POS Text Display Triplex ModeConditional Indicators Status Display BoxReverse Play Button Jog / Shuttle Freeze Button Stop Button StopZoom and Function Button Print Image FeatureNumber Button Sequence Button Conditions Printer SetupEquipment Available Menus Accessing The Menu SystemMenu System Overview Menu Notation In This ManualOpening the Drop Down Menus Rotate the Jog Menus In This ManualNavigating The Menu System Menu ShortcutsMain Menu → Time/Date → Time / Date Display Main MenuTime/Date Main Menu OverviewMain Menu → Time/Date → Set Master / Slave Main Menu → Time/Date → Set Date FormatMain Menu → Time/Date → Set Date Main Menu → Time/Date → Set Region Main Menu → Time/Date → Network Time SetupMain Menu → Sequencing → Fullscreen Dwell RecordMain Menu → Sequencing → Multiscreen Dwell Record Quality Picture Quality Disk Space Needed Main Menu → Record → Record TimerMain Menu → Record → Event Settings Main Menu → Record → Record QualityCamera 1 0.40 pps 2.5 spp Main Menu → Record → Timelapse Record RateMain Menu → Record → Activity Record Rate Main Menu → Record → Event Record RateDays 16 h Total Main Menu → Record → Alarm Record RateWrite Once Main Menu → Record → Record ModeMain Menu → Record → Disk Maintenance No OverwriteShould not be the only alarm device on site AlarmsMain Menu → Record → Auto Delete Mode Main Menu → Alarms → Input ConfigurationMain Menu → Alarms → Alarm Action Main Menu → Alarms → Alarm Latch∙ Enable All ∙ Disable All Main Menu → Alarms → Alarm Record ModeMain Menu → Alarms → Enable / Disable Main Menu → Alarms → Alarm HistoryMain Menu → Alarms → Buzzer Setup Main Menu → Alarms → Link To a MacroMain Menu → Alarms → Fullscreen Alarm Main Menu → Alarms → Relay ConfigurationEmail Notification Setup Main Menu → Alarms → Videoloss ActionMain Menu → Alarms → Pre Alarm Duration Main Menu → Alarms → NotificationEnable TCP/IP Notification SetupMain Menu → Macro → Macro Record Main Menu → Alarms → Archive AlarmsMacro Main Menu → Macro → Timed Macro Start Macro Excluded FeaturesDaylight Savings Time Alternate Method Motion DetectionMain Menu → Macro → Edit Submacro Running a MacroActivity Detection Setup Main Menu → Motion Detection → Enable/Disable DetectionIndividual Enable Menu Main Menu → Motion Detection → Setup ParametersActivity Grid Setup Screen Intrusion Detection SetupMain Menu → Motion Detection → Setup Active Zones Main Menu → Motion Detection → Indicate Detection Camera SetupMain Menu → Camera Setup → Camera Titles Sensitivity ScopeCamera Title Edit Menu Main Menu → Camera Setup → AGCTitles Display Edit TitlesAuto Disable Now Main Menu → Camera Setup → Camera DisableIndividual Disable Power Up DisableLuminance Histogram Archive SetupMain Menu → Camera Setup → Camera Scope Main Menu → Archive Setup → Port SelectCommunications Audio SetupPort Pots SetupMain Menu → Communications → RS485 Main Menu → Communications → Ethernet SettingsBaud Rate Front Panel Lock Factory SettingsReturn To Factory Defaults Changing the Installer or Operator PasswordsDeactivate The Ethernet Password QuickInstall MenuEthernet Password Activate The Ethernet PasswordSystemView Menu Overview Operator MenuSystemView Menu Operator Menu OverviewView Screen Alarm ActionCamera ∙ Enable/Disable 1 = Enabled, 0 = Disabled View ScreensRecord Rate Record Timer∙ Relay Output None, 1, 2, 1+2 ∙ Link to Event Yes or No ∙ Target Size 1 through∙ Time Zone GMT+0000 ∙ QuickWave CD Write On or Off ∙ Network Address∙ Keyboard Lock On or Off ∙ Record Lock On or Off Alarm Acknowledge AlarmsAlarm Input Alarm OutputChannel Units Alarm Operations During PlaybackMonitor-B Display During Alarm Live Alarms DisplaysRecorded Alarms Alarm History BoxSearching For Recorded Alarms Search Menu Overview SearchingSearch Button Disk Analysis ScreenQuick Archive to CD Function Button Motion SearchSelecting Search Parameters Search FiltersActivate Search Search ResultsWebBrowser To access the web interface∙ The Main Viewing Area The large blue area WaveBrowser Overview and ControlsMain Viewing Area Button Panel Drop Down Volume List BoxName Code Description Example DVMRe Triplex WaveLinkFunctionality Email Links Video Technical SpecificationsGeneral ConnectionsPart Numbers AudioMotion Detection Message Type Alarm/Event FieldAlarm/Event Message StructureAlarm/Event Description Front Panel Button EmulationData Structure Data structure Configuration and StatusMacro Description Number Macro TablesMacro Functions Table Event Day Time Macro to Run Scheduled Macro TableFactory Address Warranty and ServiceFactory Service Advance Replacement Policy Warranty and Return Information0150-0193F