Sony SA-N11, HCD-T1, TC-TX1 manual Recording a CD, etc., Manually, To stop recording, Cdcd

4 Slide DIRECTION to select dual or single-sided recording.

To record on	Slide DIRECTION to
One side	A
Both sides*	a

*Recording always stops at the end of the reverse side. Be sure to start from the front side.

5 Press CD SYNC.

The cassette deck stands by for recording, and the CD player stands by for playing.

6 Press (or 9 to select the tape side to start recording on.

To start from the front side, press (. To start from the reverse side, press 9. (Recording will be made only on the reverse side.)

7 Press P.

Recording starts. After about 10 seconds, the CD starts playing.

To stop recording

Press pon the deck or the CD player.

To activate DOLBY NR

When you want to reduce the hiss noise in low-level high-frequency signals, slide the DOLBY NR switch to ON after step 4.

About CD SYNC (synchronized) recording

With this feature, the cassette deck records a CD synchronizing with the length of the tracks on the CD, so you do not have to worry about the tape direction or remaining time while recording.

This stereo system uses the Fade Synchronized recording feature. With this feature, the deck slowly fades out a recording so that a track is not abruptly cut off at the end of the tape.

If the tape reaches the end of its front side while recording a track, the deck re-records it automatically after rewinding the tape to the beginning of the track. This time, the track is recorded with a fadeout at the end of the tape. (Recording ends at this point if it is a single-sided recording.)

Recording in the original track order of the CD

When the track order has been programmed and the total length of the tracks to be recorded is shorter than the length of one side of the tape, the unit automatically operates as follows:

When the CD player is paused, the deck continues recording silence until it reaches the end of the front side; then it reverses the tape and starts recording.

Front side

1	2	3	4	5
9	8	7		6

Reverse side

Once all of the selected tracks have been recorded, the deck records about four seconds of silence and then stops.

Recording a CD, etc., Manually

You can record a CD as you like, for instance, record just the songs you want, or you can record from any point on the tape.

Tuner CD player

POWER → ON

Stereo cassette deck	6
	p
	7
	5
1
	3
	4

2 Press FUNCTION repeatedly until the source you want to record appears in the display.

SourceIndication

CDCD

Radio TUNER

MD, etc. MD

3 Slide DIRECTION to select dual or single-sided recording.

To record on one side, set to A. To record on both sides, set to a.

4 When you want to reduce the hiss noise in low-level high-frequency signals, slide DOLBY NR to ON.

5 Press rREC on the deck.

The deck stands by for recording, and the rREC button lamp and the P button lamp on the deck light up. Either the ( or 9 button lamp lights up, and the other flashes and goes out. If the ( or 9 button lamp does not light up or frash, the corresponding tab on the cassette has been removed. You cannot record on this side.

6 Press ( or 9 to select the tape side you want to start recording on.

To start recording on the front side, press (.

To start recording on the reverse side, press 9.

7 Press P on the deck. Recording starts.

When you set the DIRECTION switch to a, recording stops at the end of the reverse side.

8 Start playing the sound source.

To stop recording

Press pon the deck.

Note

If you press FUNCTION while recording, the sound source will be switched to another.

GB

13

Front side

Reverse side

The track at the	Recording starts
end of the reverse	from the track that
side is also faded	was faded out at
out if it does not	the end of the
fit in the tape	front side.
length.

6

2

1 Press 6EJECT and insert a blank tape.

Chapter 4: the Tape Player