Arcam BDP100 manual System, Wired Network, Network Test

Parental Control – Set whether Parental Control is On or Off.

<Off: All discs are played back.

<On: Disc palyback is restricted according to the Parental Level set in the following menu item.

Parental Level – Set the degree of disc restriction. The lower the value, the stricter the limitation.

<1 [Kid Safe]: Suitable for children.

<2 [G]: General audience.

<3 [PG]: Parental Guidance suggested.

<4 [PG-13]:Unsuitable for children under 13.

<5 [PG-R]:Parental Guidance Recommended.

<6 [R]: Restricted; cinemas require children under the age of 17 to have an accompanying adult parent or guardian.

<7 [NC-17]:Cinemas do not admit anyone younger than 17 years old.

<8 [Adult]: Discs of any rating (Adult/General/ Children) can be played back.

Parental Password – Press >with this option highlighted to enter a new password. Enter a new 4-digit code using the numeric buttons on the remote control, then navigate to the on-screen ok button using the remote control cursor keys, then press ok on the remote control. You will be prompted to re-enter the code for confirmation, repeating the process above.

Please enter a new Parental Control Password:

P arental P assword

OK C ancel

System

Optical Disc Autoplay – controls whether an optical disc (e.g. Blu-ray Disc, DVD, CD) will play automatically after it has loaded.

<On: Optical discs will play automatically.

<Off: play must be pressed to play a disc.

BD-Live Internet access – sets restrictions on Internet access.

<Limit Access: Only allows Blu-ray discs with owner certification to access the Internet.

<Always Allow Access: All BD-Live discs are allowed access to BD-Live websites.

<Prohibit Access: Prohibit all BD-Live discs from accessing BD-Live websites.

note

<The available on-line functions are disc- dependent.

<Refer to the BD-Live disc instructions for information about accessing on-line content.

<The BDP100 must be connected to the Internet and set up correctly to allow access to on-line content. See page E-9 for network connectionsandpageE-22fornetworksettings.

BD-Live Storage – BD-Live content is stored in the attached USB memory device. This menu item displays the amount of USB memory remaining.

Erase Blu-Ray Storage – Press ok with this item highlighted to erase the BD-Live content stored on the USB storage device.

Screensaver duration –sets the duration of static image display before the screensaver is shown. The screensaver prevents screen damage due to burn-in of a static image.

<Off: Deactivates the screensaver function.

<5/10/20/30 minutes: sets the period of time that a static image can be displayed before the screensaver activates.

note

<The screensaver can be deactivated by pressing any button on the unit or remote.

Reset Settings – Press ok with this item highlighted to reset all settings to factory defaults (except parental controls).

Network

An active, configured Internet connection is required if you wish to use BD-Live websites and downloaded content. See page E-9 for physical connections.

Most home networks will automatically configure the connection using DHCP. If your network is not configured automatically, you will need to know the following settings:

<IP Address

<Subnet Mask

<Gateway

<Primary DNS

<Secondary DNS

Wired Network

Select and press OK to set the network connection parameters:

Link Status – Information only MAC Address – Information only

IP Mode – Set whether the network settings are automatic or set manually.

<Off: Disables network functions.

<Manual: Enter settings manually, for expert users.

<Dynamic: Allows the connected router or modem to configure the network settings automatically, using the network’s DHCP server. This setting should be used for the majority of home networks.

The following settings are only available when IP Mode is set to Manual:

IP Address – Press OK to set the IP address assigned to your player by your network administrator. Use the cursors to navigate between segments and use the numeric keys on the remote control to enter the address. Navigate to the on-screen OK button and press OK on the remote to save the setting.

Subnet Mask – Press OK to set the subnet mask of your network. Use the cursors to navigate between segments and use the numeric keys on the remote control to enter the subnet mask. Navigate to the on-screen OK button and press OK on the remote to save the setting.

Gateway – Press OK to set the IP address of your Internet gateway. Use the cursors to navigate between segments and use the numeric keys on the remote control to enter the address. Navigate to the on-screen OK button and press OK on the remote to save the setting.

Primary DNS – Press OK to set the IP address of your Primary DNS server. Use the cursors to navigate between segments and use the numeric keys on the remote control to enter the address. Navigate to the on-screen OK button and press OK on the remote to save the setting.

Secondary DNS – Press OK to set the IP address of your Secondary DNS server. Use the cursors to navigate between segments and use the numeric keys on the remote control to enter the address. Navigate to the on-screen OK button and press OK on the remote to save the setting.

Network Test

Press OK to run a network test. This will also configure the network settings automatically if they have not been configured and if automatic configuration (DHCP) is supported by the network.

E-22