RCA RCU1000B warranty Deleting An Event Timer, Learn IR Mode, Tips On Learning

Page 19

RCU1000B_IB.qxd 10/9/01 11:09 AM Page 19

Deleting An Event Timer

Any set Timer Event is indicated by the symbol (T) displayed above the clock. If no Timer events have been set then this option is not shown in the Setup screens.

1.Press and hold the SETUP key until the LCD displays “Delete a Timer?” and the LED remains on. Release the SETUP key. Press and release OK on the LCD.

2.Delete X?É..DAY HH:MM” is displayed where DAY is current day, HH:MM is timer event time and X is the Timer event (1, 2, 3, or 4). Press the SETUP key repeatedly until the Timer Event you want to delete is displayed.

3.To delete this Timer event, press and release OK. To skip canceling this event, press and release the SETUP key to advance to next setup option.

4.Confirm to Delete?” is displayed. Press and release the OK on the LCD. The display returns to either “Delete a Timer?” or, if no more Timer events are set, to “Exit Setup”.

OR

5. Deleting a Timer is now complete.

Learn IR Mode

The Learning feature is used as a supplement to the standard preprogrammed library. The standard code library provides most of the functions needed, but you can add a small number of additional functions of you choice. You can store original remote commands consisting of up to 39 keys for each of the RCU1000B’s 9 Device Modes. Only one original remote type can be stored under any one device.

Tips On Learning

1.Use fresh batteries for both the RCU1000B remote and your original remote(s).

2.Experiment by Learning 2 or 3 keys initially (to ensure compatibility and familiarity) and then carry out the setup routine “Delete IRÉ.ALL?” before completely Learning your original remote’s keyboard.

3.Place the original remote to the rear of the RCU1000B so that the IR LED sensor on the front of the original remote is in line with the RCU1000B’s IR sensor, located near the quick key area. Keep the distance between the two remotes to approximately 2 inches.

4.If commands were learned previously, carry out the setup routine “Delete IR...ALL?” before attempting any new Learning.

5.Do not attempt to Learn directly under an incandescent or low-energy light as these can cause interference with the IR transmissions. Keep at least three feet away from any such light sources.

6.When the memory is full, the display shows “MemoryÉ.Full” and the visible LED flashes for two seconds. It is not possible to Learn any additional keys without clearing a Device first.

7.When Learning a key, do not release the key being Learned until the display shows “Success” followed by “Learn IR...Key?”.

8.All Learned commands are saved automatically, there is no “Confirm to Save” screen.

19

Image 19
Contents Touchscreen Table Of Contents To install the batteries Battery InstallationRCU1000B LCD Glossary Of TermsTvvcr Setup Button Quick Reference Guide To search for a code instead of using the code library listTo learn a command To delete stored learned commands under a deviceTo program a macro To delete all stored learned commandsTo set a timer event To exit setup while in setup modeTo set the LCD on time Direct Code EntryTo set the light on time Code Search Code Identification Code Search NotesAuto Search 003, 004, 009, 022 TV Code ListWards VCR Code ListDVD DVD Code ListCable Code List Satellite Code ListAudio Receiver Tuner Audio Component Code ListKey Label Mode Setting Up An Event Timer Learn IR Mode Deleting An Event TimerTips On Learning To Learn Commands Learned Key Reference To Delete ALL Stored Learned Commands To Delete a Stored Learned CommandTo Program a Macro Displays PressDigit For Delay?Exit Setup Reset AllTo Delete a Macro To Set The Time and Day for Normal LCD Display Setting More OptionsTo Set Keypress Beep on or OFF To Set LCD Light On-Time General Notes RCA All Power Off FeatureVCR/DVD Punch-Through VCR RecordLimited 90 Day Warranty TroubleshootingHelpline Inside Card RCU1000B Product Registration Card