RCA RCU1000B warranty VCR/DVD Punch-Through, VCR Record, RCA All Power Off Feature, General Notes

Page 28

RCU1000B_IB.qxd 10/9/01 11:10 AM Page 28

Setting More Options continued

5. If TV was selected, go to step 6 below. If Audio was selected, the display shows the “Set VolumeÉ. AudioMode?” prompt for Audio Mode to be used for Volume/Mute control. Press and release desired Audio Mode and press and release OK to confirm to save.

6. The LCD displays “Set more Options”. Press EXIT on the LCD.

Notes

VCR/DVD Punch-Through

The remote will punch-through to VCR or DVD mode, whichever was last used. Punch- through to VCR/DVD Mode carriage keys is only allowed for TV, VCR, DVD, and Cable coded Modes. SAT/DBS and CD/Audio are dedicated to their Modes. The LCD shows device change for the VCR/DVD punch-through keys if they are pressed in other Modes, e.g. if you are in Cable Mode and you press PLAY, VCR (or DVD) is displayed in the LCD.

VCR Record

In VCR Mode (including punch-through), the RECORD key has to be pressed twice before the command is sent. This is also true if a VCR type is programmed under any other device. The exception is for DVD where the RECORD key transmits the IR command after only a single press of RECORD. For any programmed SAT/DBS Mode the RECORD key only needs to be pressed once. In any CD/Audio Mode, the RECORD key must be pressed twice.

RCA All Power Off Feature

This feature is available in all normal operating Modes. If the POWER key is pressed consecutively twice within 2 seconds ALL RCA equipment will be turned off. The LCD shows “Power Off” while this routine is active.

General Notes

1.When in Setup Mode, pressing the LEARN key jumps you to the “Learn IR Mode?” screen.

2.When in Setup Mode, pressing the MACRO key jumps to the “Setup a Macro?” screen.

3.At any point in Setup, where a “save” is being made, “Confirm to Save?” is displayed. You then press [OK] to save, or [EXIT] to return without saving any changes.

4.At any point in Setup, where an “overwrite” is being made e.g. overwriting Macro’s, Learned Modes, etc., “Confirm to Overwrite?” is displayed. You then press [OK] to confirm the change, or [EXIT] to return without any saving any changes.

5.At any point in Setup, where a “deletion” is being made e.g. deleting Macro’s, Timers, etc., “Confirm to Delete?” is displayed. You then press [OK] to confirm the deletion, or [EXIT] to return without deleting anything.

6.At any point in Setup, where a “change” has been made a “Success” message is displayed for 1 second to confirm the action.

28

Image 28
Contents Touchscreen Table Of Contents To install the batteries Battery InstallationRCU1000B Glossary Of Terms LCDTvvcr Setup Button To search for a code instead of using the code library list To learn a commandTo delete stored learned commands under a device Quick Reference GuideTo delete all stored learned commands To set a timer eventTo exit setup while in setup mode To program a macroTo set the LCD on time Direct Code EntryTo set the light on time Code Search Code Identification Code Search NotesAuto Search TV Code List 003, 004, 009, 022VCR Code List WardsDVD Code List DVDSatellite Code List Cable Code ListAudio Component Code List Audio Receiver TunerKey Label Mode Setting Up An Event Timer Learn IR Mode Deleting An Event TimerTips On Learning To Learn Commands Learned Key Reference To Delete a Stored Learned Command To Delete ALL Stored Learned CommandsDisplays PressDigit For Delay? To Program a MacroExit Setup Reset AllTo Delete a Macro Setting More Options To Set The Time and Day for Normal LCD DisplayTo Set Keypress Beep on or OFF To Set LCD Light On-Time RCA All Power Off Feature VCR/DVD Punch-ThroughVCR Record General NotesLimited 90 Day Warranty TroubleshootingHelpline Inside Card RCU1000B Product Registration Card