Bosch Appliances DVR 480, DVR 440 operation manual 6USB connectors, RS485 port, Gnd

Page 25

Digital Video Recorder 440/480 SeriesHardware setup en 25

4.6USB connectors

A USB 2.0 connector is located at the rear panel of the unit to which a mouse, for example, can be connected. For convenience, the USB 2.0 port is located on the front of the unit to connect a mouse or USB memory device. (Recording to a USB-drive is not supported.)

	Figure 4.7 USB connector (on front and on rear)
4.7	RS485 port

Connect Bosch or third-party controllable cameras to the unit for pan, tilt, and zoom control. The Bosch protocol is supported with the following baud settings:

–9600 baud

–8 data bits

–1 stop bit

–no parity

–no flow control

Figure 4.8 RS-485 connector

Signal name	Pin number	Description

TX -	1	Data transmission

TX +	2	Data transmission

GND	3	Shield

Table 4.3 RS485 pin definition

The recommended cable cross section is AWG 28-16 (0.08-1.5 mm2).

Bosch Security Systems

Installation and Operation manual

AM18-Q0605 v2.0 2012.04

Image 25

Contents Digital Video Recorder 440/480 Series Page Table of Contents Configuration menu MaintenanceCamera Maximum frame rates DVR Video adjustment Operating instructionsDdns TCP/IPNTP Web Client SoftwareAppendix Menu default values Technical specificationsSafety precautions 1SafetyImportant safety instructions En Safety Digital Video Recorder 440/480 Series Coax grounding Important NoticesRack-mount FCC Information FCC and ULCopyright Bosch noticesTrademarks More informationDigital video recorder applications IntroductionVersions ManualsPackage contents FeaturesUnpacking 5Warranty Installation environmentAssociated equipment Powering up Quick installConnections Primary connectionsNavigating First-time useInternational Quick install menuContinuous Recording Quick install Continuous RecordingIP address, Subnet 3NetworkMask, and Gateway Specifications Hardware setupCamera connections Audio connectionsMonitor connections Monitors or larger when using LCDsVGA Monitor a 2CVBS4RS-232 COM port connections Signal name Pin number DescriptionRTS CTSLantx 5Ethernet connectionLanrx + RS485 port 6USB connectorsGND Connecting the inputs 8External alarm I/O connectionConnecting the alarm output 10Maintenance 9Power supplyView live Yes Sequence Quad Operating instructionsOSD 1Keys Front panel controlsArrow keys AM18-Q0605 v2.0 Bosch Security Systems 2Indicators Mouse Controls Remote controlKey. To close the System Control Bar press the exit Monitor a Viewing picturesMonitor B 3Viewing Zoom Freeze imagePlayback mode Live modeAdministrator. To enter playback mode To switch the unit from live to playback modeAccess using the mouse Access using the front panel keysOverview of the menu system System Control Bar appears on monitor aMain menu Main menu Search Bosch Security Systems AM18-Q0605 v2.0 7SearchDate/time search Search criteria Event searchSearch results Event Search resultsSmart Search results Smart search10 Export menu 8Export11 System Control Bar System information System information12 System Control Bar Video signals information 13 System Control Bar Disk info Logbook filter 10LogAlarm inputs Triggers and alarmsMultiple alarms Video loss alarmMotion events System Configuration menu Configuration menuTop tabs Submenus Camera 1Camera 1CameraChannels Enabled Video adjustmentMaximum frame rates DVR ChannelCamera PTZ 5PTZCamera Continuous Recording Input Recording Use the same procedure as in Continuous RecordingPre-event Post-eventMotion Recording Use the same procedure as in Input Recording25/30 Network Live StreamingCamera Video format Video format2Schedule Setting the dynamic characteristics1Schedule 3Display Use the same procedure as Monitor a1Language Exception days1Input 4EventInput Type Relay output13 Event Motion 2Motion14 Event Alarm acknowledge Alarm acknowledgeSystem menu Relay outputs can be configured to react to system events1TCP/IP 5Network2Streaming to mobile devices 3Connecting using a smart mobile phone 5Notification 4DDNS6Mail 1Date/Time 6System2NTP 3Beeper4Users AdminGeneral User 1, 223 System Configuration 5Configuration24 System Hard disk Hard Disk25 System System 7SystemWeb Client Software Connecting to the DVR 400 Series the first timeGetting started System requirementsSettings behave differently because of the Web Browser How to log onMenu structure differences Maximum number of usersIntroducing the browser window Live modePTZ camera control Pan and tiltCamera views Aux commandsZoom, focus, and iris Pre-positionWeb Client Playback Bosch Security Systems AM18-Q0605 v2.0 Playback modeWeb Client Export AM18-Q0605 v2.0 Bosch Security Systems Export modeConfiguration mode Archive Player InstallationStarting the Program Authenticity of the archived videoIntroducing the main window To switch the display modeCamera Views Open buttonViewing Images Using the playback controlsAssigning Cameos Video slider bar Find imageChecking authenticity Exit buttonNavigation Setting Default value Reset Menu default valuesNavigation Setting Default value Reset Rtsp Port TCP/IP DhcpIcmp EmptyYYYY/MM/DD AdministratorDVR ID 10.1 Electrical Technical specifications10.1.2 Environmental 10.1.1 MechanicalStorage Display Modes10.2 USB memory sticks Electromagnetic and SafetyEMC requirements USASoftware licenses AppendixBosch software Other licenses copyright noticesSource license Warranties and disclaimer of warrantiesRelevant open source software can be found at InformationPage Bosch Security Systems

4.6USB connectors

Figure 4.7 USB connector (on front and on rear)

RS485 port

Figure 4.8 RS-485 connector

Signal name

GND

The recommended cable cross section is AWG 28-16 (0.08-1.5 mm2).