Sylvania 6900DTE Display Mode, Important information about screen ratio and display mode, 43 TV

Page 42

Advanced Operation

DISPLAY MODE

1 Press SETUP to display SETUP menu.

Screen:

Remote:SETUP

QUIT

CHANNEL

DISPLAY

CLOCK

DETAIL

2 Select DISPLAY using navigation buttons o / p, then press ENTER.

•DISPLAY menu appears.

DISPLAY

QUIT

16:9

SCREEN RATIO

CHANNEL DISPLAY MODE

SIDEBAR

DISPLAY

 

CLOCK

 

DETAIL

 

3 Select DISPLAY MODE using navigation buttons o / p, then press ENTER.

•Display mode options appear.

DISPLAY

 

 

QUIT

SCREENSelect

display mode.

 

CHANNEL

DISPLAY

SIDEBAR

 

 

DISPLAY

 

ZOOM

 

 

CLOCK

 

 

 

 

FULL

DETAIL

 

 

4Select the desired display mode using navigation buttons o / p, then press

ENTER.

•The display mode is set.

DISPLAY

QUIT

16:9

SCREEN RATIO

CHANNEL DISPLAY MODE

SIDEBAR

DISPLAY

 

CLOCK

 

DETAIL

 

NOTE:

Choose the display mode as you prefer.

See “INFORMATION on Screen Ratio and Display Mode” on page 43 for further information.

5 Press SETUP to exit SETUP menu.

42

EN

CAUTION:

If the TV is left in LETTERBOX or SIDEBAR for a long period of time, the still image may cause a burn-ing effect, damaging the TV screen.

Important information about screen ratio and display mode

Depending on the type of TV you have, you may encounter one of the following problems.

4:3 TV

If you have a 4:3 aspect HDTV, bars may appear at the top and bottom of the picture when you input 1080i signals. If you have set the STB to SCREEN RATIO 16:9 and SIDEBAR, the screen may appear as shown here.

appears because of TV settings.

1080i video

4:3 TV

STB output signal

appears because of STB settings.

We recommend setting the STB’s screen ratio to 4:3 and the display mode to suit your preference. Alternatively, set the resolution selection switch on the rear panel to “480p”. See your TV owner’s manual for details.

16:9 TV

A double set of sidebars may appear on the left and right of the picture, squeezing it into the center of the screen. This can occur if you have set the resolution selection switch on the rear panel to “480p”, because the television may recognize the signal as 4:3, regardless of the screen ratio setting you have made on the STB.

appears because of TV settings.

16:9 TV

480p video

STB output signal

appears because of STB settings.

If your television can handle 1080i or 720p signals, set the resolution selection switch on the rear panel to the resolution for your television. If it cannot handle either of these, then change the display mode on your television.

1A23

Page 41 Page 43
Image 42
Page 41 Page 43
Contents 6900DTE Table of Contents IndiceImportant Safeguards S2 8 9 8 a Precautions LocationInformation on digital broadcasting Receives AtscSub-Channel Major features of STBDolby Digital Smart AntennaLocation of controls Navigation buttons o / p / s / B Moves12 11 Accessories Installing batteries Snap the battery cover backConnecting the Smart Antenna For details Rear panel of STBConnecting a different antenna Cable BOXRefer to your television’s manual for details Antenna Connections STB connection using DVI-D Hdcp OUT jack to Hdtv Connections TV/Monitor STB connection using COMP. OUT jacks to Hdtv TV/Monitor Connections Connection to Sdtv STB connection to a decoder with Dolby Digital Digital DecoderSTB connection to a standard stereo system Stereo Component4Other Connections Initial setup Select Setup using navigation buttons Then press EnterSTB starts scanning channels Setup Wizard 4/8 appears Setup Wizard 3/8 appearsPress Enter when the cursor is on SET Setup Wizard 5/8 appearsSetup Wizard 8/8 appears Setup Wizard is completed. STB starts receiving broadcastsTo select SET and press Enter Selecting channels PowerWatching TV Enter CH ReturnAtsc About sub-channel broadcastingTo select only with a main channel number E.g To return to the channel you were last watchingPress Info to clear Channel bannerPress Info to display the channel banner InfoLock Components of Channel BannerDTV CHIP/CCAudio map Choosing audio and languagePress Audio AudioPress any button to quit Picture StillPress Still o button while watching StillScanning No SignalOn screen messages Restricted ProgramPrevious Press EPG button while watching TVPress Enter EPGComponents of Electronic Program Guide EPG To clear the EPGSetup menu options Adding/Deleting channels Press Setup to display Setup menuSetup Channel menu appearsPress Setup to exit Setup menu Select ADD using navigation buttons o Then press EnterPress Enter when the cursor is on the digital channel Enter channel numberInformation on channel map Adjusting antenna Navigation buttons To adjust channelAntenna Receiving channels Antenna to get the best receptionAutoscan Autoscan Cancelled appears on the screen To cancel during scanningWhen no Signal appears on the screen Scan is completedDisplay menu appears Selecting screen formats Screen ratio and Display modeScreen Ratio Screen ratio options appear43 TV Display ModeImportant information about screen ratio and display mode 169 TVFull Letter BoxZoom SidebarSetting the clock Select Clock using navigation buttons Then press EnterSelect DST using navigation buttons o / p, then press Enter Your settings are activated Time Zone setting menu appearsCurrent time setting menu appears To go back and forth, press navigation buttons s / BWhen not using the auto-clock setting Adjusting the clock AutomaticallySelect Auto using navigation buttons Then press Enter After scanningSetting a new password Chip optionsSelect Detail using navigation button Then press Enter Enter the default passwordCHIP/CC menu appears Setting for V-CHIP/CC Select Detail using navigation buttons Then press EnterEnter your 4-digit password CHIP/CC setting menu appears If you choose STBto control V-CHIP RatingsIf you choose TVto control V-CHIP Ratings Setting Mpaa rating Mpaa RatingLock indicators are added to programs rated PG-13 and above Select Detail using navigation buttonsMpaa rating setting menu appears To block all PG-13 moviesSetting TV rating TV RatingTV rating setting menu appears Information on TV ratingsPress Setup to exit Setup menu To set age-based ratings To block all TV-14 programsCC3 and TEXT3 Closed caption optionsClosed Caption CC2, CC4, TEXT2 and TEXT4Closed Caption selection screen appears Then press Enter Enter your 4-digit passwordClosed Caption menu appears Closed Caption menu appears Your selection is activatedGo to step Select SET using navigation buttons s Then press Enter Opacity selection screen appearsCC Style preview screen appears Language menu appears Choosing the screen languageMenu Language Language you select is now used for on-screen displaysSound effects are only when using on screen menu Choosing sound effectsSound Effects Troubleshooting Extended Scan Specifications Glossary and AcronymsElectronic Program Guide EPG PasswordDigital Audio OUT OPT. or COAX. jack Video output jackMando a Distancia Antes de utilizarUbicación del control Panel FrontalConexiones de antena Conexiones de TV/MonitorDVI-D Hdcp OUT en Hdtv Otras conexiones Conexión STB a un Decodificador con Dolby DigitalConexión STB a un sistema Estéreo normal Ajuste inicialConsejo Memo Van Ness Avenue, Torrance, CA 0EMN02517
Top Page Image Contents