Philips VRX463 warranty Setting Up the VCR Plus+ Programming System cont’d

Page 39

Setting Up the VCR Plus+ Programming System (cont’d) 39

2

Now, compare the channel numbers you have written into the VCR PLUS+ CH. and CABLE/TV CH. columns. You’ll notice that some stations have VCR Plus+ and Cable/TV channel numbers that are the same, and other stations have channel numbers that do not match. Where the channel numbers DO NOT match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers according to the following steps.

3

Press the VCR button, then press the MENU button.

TO SELECT PUSH NO. SHOWN

1PROGRAM

2VCR SET UP

3TUNER SET UP

4INPUT SELECT

5SET CLOCK

6SET REMOTE LOCATOR

TO END PUSH EXIT

4

Press the Number 2 button to select VCR SET UP.

TO SELECT PUSH NO. SHOWN

1 SET REPEAT PLAY (OFF)

2 ON SCREEN MODE

3LANGUAGE

4SET VCR PLUS+ CH

5SET CABLE BOX

6SET DSS RECEIVER

7AUDIO OUT

8 VIDEO STABILIZER (OFF) TO END PUSH EXIT

5

Press the Number 4 button to select SET VCR PLUS+ CH.

2Examine the lists on page 38.

	CBL/DSS	VCR	TV	3
	PAUSE/STILL	POWER	MUTE
	REW	PLAY	FF
	REW		FF
7	EJECT	STOP	F.ADV
		STOP
	VCR PLUS+/ENTER
	EXIT/STATUS		CLEAR
		MENU
	JOG/SHUTTLE			6
	JOG/SHUTTLE
	VOL		CHANNEL
			CHANNEL

4	1	2	3
5	4	5	6
5	7	8	9
	100	0	GO-TO

REC /OTR	INDEX	MEMO
	VAR.
	SLOW
SPEED	VCR/TV SLOW	TRACKING SKIP
		SEARCH

6

Look at the columns you filled in on page 38. For stations whose VCR Plus+ and Cable/TV channels are not the same, use the CHANNEL Up/Down buttons to place the arrow beside the VCR PLUS+ channel. Then, press two Number buttons to enter the CABLE/TV channel. Entries must be made within one minute. If you enter the CABLE/TV channel incorrectly, you may enter it again.

Do this until you have entered all the channels on your list.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

01	– – – – –> 33
02	02

TO SELECT CH PUSH CH UP/

DOWN, THEN ENTER CH. NO.

TO END PUSH EXIT

7

Press the EXIT/STATUS button to exit.

REMOTE LOCATOR

Helpful Hints

•To check the VCR PLUS+ and CABLE/TV channel listings, follow steps 3 - 5 above. A list of VCR PLUS+ and CABLE/TV channel num- bers will appear on-screen. To move through the list, press the CHANNEL Up/Down buttons. Make sure these numbers match your lists on page 38. Press the EXIT/STA- TUS button to exit.

•When you receive the VCR from the factory, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the same in the cross reference map.

Image 39

Contents Video Cassette Recorder VRX463 For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents VCR Maintenance Before Using Your VCRPutting Batteries in the Remote Control Using the Remote ControlDisconnect the antenna or cable from your TV Hookups Without a Cable BoxAntenna Or Cable Hookups Without a Cable Box cont’dWatching TV With the VCR Turned Off Timer RecordingsHookups With a Cable Box/DSS Receiver Recording or Viewing a Scrambled or Unscrambled ChannelAntenna in Jack On back of TV Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Playing a TapeTurn on the TV Press the VCR button, then press the Power buttonTurning on Your VCR VCR will come onWait for the VCR to program channels Press the Menu button. The menu shown below will appearBring up the main menu display Press the Number 3 button to select Tuner SET UPProgramming Channels Press the VCR button, then press the Menu button toPress the Number 4 button to select ADD/DELETE CH Adding/Deleting ChannelsPress the VCR button Press the Menu button to bring up the main menu displayPress the EXIT/STATUS button Setting the ClockPress the VCR button, then press the Menu button Press the Number 3 button to select SET Manual ClockSetting the Clock cont’d Time Zone SelectionPress the Number 4 button to select SET Time Zone Manual PBS Channel Selection Automatic PBS Channel Selection Setting the Clock cont’dPress the EXIT/STATUS button to exit Daylight-Saving Time SelectionPress the Number 3 button to select Language Press the Number 2 button to select VCR SET UPLanguage Selection Language SelectionRemote Control Buttons JOG/SHUTTLE Button REWind ButtonStop Button Eject ButtonDisplay Panel Tape Speed Lights Memory Light Display Panel cont’dOTR Light Remote SensorFront Panel Rear Panel 2Find the code for your TV 4Repeat step Setting the Remote Control to Operate a TVFind the code for your Cable Box/DSS Receiver Repeat step Cable BOX/DSS Receiver CodesSound Program Press the Number 2 button to select on Screen ModeOn-Screen Status Displays Counter will remain on the screenRemote Locator When you find the remote control, point the remote atPlaying Read and follow the steps below to play a tape1Turn on the TV 2Insert a tape Appear on the display panel RecordingOne Touch Recording Starting an OTRStopping an OTR Recording One Channel/Watching Another Recording Timer RecordingPress the Number 1 button to select Program Select a once, daily, or weekly recordingInstructions continue on Box/DSS Receiver onFollow to set the recording’s stop time Tape Speeds Timer Recording cont’dChecking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV Channels Cable ChannelsLocal TV Stations Call letters Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Cable Box or DSS Receiver Controller Connecting the ControllerPress the Number 5 button to select SET Cable BOX Setting the Controller to Operate a Cable BoxPress the Menu button or the EXIT/STATUS button Ton. When the Cable Box changes to channel 09, go to stepPress the Menu button. Wait for a few seconds Number 2 button to select NO. Use the Number buttons toPress the Number 6 button to select SET DSS Receiver Press the Number 1 button to set the DSS ReceiverController to on Press the Number 1 button to select YES Press the Menu buttonVCR 1 will play your tape. Insert a prerecorded tape in VCR Rerecording Tape DuplicationAudio cables Video cableInsert a tape Index SearchMulti-Channel Television Sound System Receiving a Stereo BroadcastReceiving a Second Audio Program Press the Number 1 button so that on appears beside Multi-Channel Television Sound System cont’dHi-Fi Stereo Tape Playback Tape Counter Memory Using the Tape CounterTurn off VCR To bring up the Goto displayBegin tape playback Stop the tapeRepeat Playback Video Stabilizer Video StabilizerViewing a Slow Motion Picture Playback OptionsForward and Reverse Searching Viewing a Still PictureAutomatic Operation Features Cable Box/DSS Receiver Output Channel channel 03 or GlossarySpecifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories