Philips VRX463 warranty Press the EXIT/STATUS button. Program WAS COM

Page 41

Timer Recording With the VCR Plus+ Programming System (cont’d) 41

5

Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. You cannot use the (Tape) SPEED button at this time.

ONE TIME PROGRAM

PROGRAM	2
CHANNEL	25 CABLE/TV
TIME ON	10:00 AM
TIME OFF	01:00 PM
REC SPEED	SLP

START DATE 07/10/97

THU.

PUSH 1=SP OR 2=SLP

TO END PUSH EXIT

6

Press the EXIT/STATUS button. PROGRAM WAS COM-

PLETED/PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen. (If PROGRAM NOT COMPLETED appears, begin again from step 1.) After five seconds, the on- screen display will disappear.

7

Press the POWER button to turn off the VCR. The VCR must be turned off for a timer recording to take place.

The TIMER light will appear on the display panel of the VCR when you turn off the VCR. The TIMER light and the Cassette-Inside light will flash if there is not a tape in the VCR.

The VCR must be off for a timer

recording to take place!

Make sure a tape is in the VCR.

7

6

5

CBL/DSS	VCR	TV
PAUSE/STILL	POWER	MUTE
REW	PLAY	FF
REW		FF

EJECTF.ADV

STOP

VCR PLUS+/ENTER

EXIT/STATUSCLEAR

		MENU
	VOL	JOG/SHUTTLE
	VOL	CHANNEL
		CHANNEL

1 2 3

4 5 6

7 8 9

100 0 GO-TO

REC /OTR

INDEX

MEMO

VAR.

SLOW

SPEED VCR/TV SLOW TRACKING SKIP

SEARCH

REMOTE LOCATOR

Helpful Hints

•To exit the VCR Plus+ programming system at any step, press the EXIT/STATUS button.

•PROGRAM NOT COMPLETED/ CLASH may appear on-screen for five seconds at step 6 if the timer recording you programmed overlaps with another timer recording. Then, the timer recording menu will appear. To cancel the overlapping timer recording, follow the steps on page 37.

Image 41

Contents Video Cassette Recorder VRX463 For Customer Use Dear Philips Magnavox product ownerIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Before Using Your VCRUsing the Remote Control VCR MaintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable BoxAntenna Or Cable Hookups Without a Cable Box cont’dHookups With a Cable Box/DSS Receiver Timer RecordingsRecording or Viewing a Scrambled or Unscrambled Channel Watching TV With the VCR Turned OffRecording One Channel/Watching Another Hookups With a Cable Box/DSS Receiver cont’dPlaying a Tape Antenna in Jack On back of TVTurning on Your VCR Press the VCR button, then press the Power buttonVCR will come on Turn on the TVWait for the VCR to program channels Press the Menu button. The menu shown below will appearProgramming Channels Press the Number 3 button to select Tuner SET UPPress the VCR button, then press the Menu button to Bring up the main menu displayPress the VCR button Adding/Deleting ChannelsPress the Menu button to bring up the main menu display Press the Number 4 button to select ADD/DELETE CHPress the VCR button, then press the Menu button Setting the ClockPress the Number 3 button to select SET Manual Clock Press the EXIT/STATUS buttonPress the Number 4 button to select SET Time Zone Setting the Clock cont’dTime Zone Selection Manual PBS Channel Selection Automatic PBS Channel Selection Setting the Clock cont’dPress the EXIT/STATUS button to exit Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons Stop Button REWind ButtonEject Button JOG/SHUTTLE ButtonDisplay Panel OTR Light Display Panel cont’dRemote Sensor Tape Speed Lights Memory LightFront Panel Rear Panel 2Find the code for your TV 4Repeat step Setting the Remote Control to Operate a TVFind the code for your Cable Box/DSS Receiver Repeat step Cable BOX/DSS Receiver CodesOn-Screen Status Displays Press the Number 2 button to select on Screen ModeCounter will remain on the screen Sound ProgramRemote Locator When you find the remote control, point the remote at1Turn on the TV 2Insert a tape PlayingRead and follow the steps below to play a tape Appear on the display panel RecordingStopping an OTR One Touch RecordingStarting an OTR Recording One Channel/Watching Another Press the Number 1 button to select Program Timer RecordingSelect a once, daily, or weekly recording RecordingFollow to set the recording’s stop time Instructions continue onBox/DSS Receiver on Tape Speeds Timer Recording cont’dChecking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Cable Box or DSS Receiver Controller Connecting the ControllerPress the Number 5 button to select SET Cable BOX Setting the Controller to Operate a Cable BoxPress the Menu button. Wait for a few seconds Ton. When the Cable Box changes to channel 09, go to stepNumber 2 button to select NO. Use the Number buttons to Press the Menu button or the EXIT/STATUS buttonController to on Press the Number 6 button to select SET DSS ReceiverPress the Number 1 button to set the DSS Receiver Press the Number 1 button to select YES Press the Menu buttonAudio cables Rerecording Tape DuplicationVideo cable VCR 1 will play your tape. Insert a prerecorded tape in VCRInsert a tape Index SearchReceiving a Second Audio Program Multi-Channel Television Sound SystemReceiving a Stereo Broadcast Press the Number 1 button so that on appears beside Multi-Channel Television Sound System cont’dHi-Fi Stereo Tape Playback Tape Counter Memory Using the Tape CounterBegin tape playback To bring up the Goto displayStop the tape Turn off VCRRepeat Playback Video Stabilizer Video StabilizerForward and Reverse Searching Playback OptionsViewing a Still Picture Viewing a Slow Motion PictureAutomatic Operation Features Cable Box/DSS Receiver Output Channel channel 03 or GlossarySpecifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories