Philips VRX463 Before Using Your VCR, Putting Batteries in the Remote Control, Erase Protection

Page 5

Putting Batteries in the Remote Control

1

To remove the battery compartment lid, push in the tab, then pull up the lid.

2

Place three AA batteries inside the battery compartment with their polarities (+ and – ends) aligned as indicated.

3

Replace the battery compartment lid.

Using the Remote Control

•Point the remote control at the VCR’s remote sensor.

•Do not put objects between the remote control and the VCR.

•Press the VCR button before pressing other VCR operation but- tons.

•Press the TV button before pressing other TV operation but- tons.

•Press the CBL/DSS button before pressing other Cable Box or DSS Receiver operation buttons.

Before Using Your VCR 5

1 2

3

Erase Protection

Video cassette tapes have record tabs to ensure that recordings are not accidentally erased.

1

To prevent accidental erasure, break off the tab with a screwdriver.

2

To record again, cover the hole with cellophane tape.

VCR Maintenance

•In this VCR, use only tapes with the mark.

•Make sure any light adhesive stick-on notes are removed from the video cassette tape before putting the tape in the VCR. Removable labels like these can jam the VCR.

•Periodic maintenance is required to maintain your VCR’s perfor- mance. Your VCR has an automatic head cleaner, but the video heads eventually will require cleaning or replacement. Cleaning or replacement of the video heads should be performed only by an authorized service center.

1 2

Helpful Hints

•The remote control and its batteries are supplied.

•Do not mix alkaline and manganese batteries.

•Do not mix old and new batteries.

Image 5

Contents Video Cassette Recorder VRX463 For Customer Use Dear Philips Magnavox product ownerIntroduction FeaturesSafety Precautions Table of Contents Putting Batteries in the Remote Control Before Using Your VCRUsing the Remote Control VCR MaintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable BoxAntenna Or Cable Hookups Without a Cable Box cont’dHookups With a Cable Box/DSS Receiver Timer RecordingsRecording or Viewing a Scrambled or Unscrambled Channel Watching TV With the VCR Turned OffRecording One Channel/Watching Another Hookups With a Cable Box/DSS Receiver cont’dPlaying a Tape Antenna in Jack On back of TVTurning on Your VCR Press the VCR button, then press the Power buttonVCR will come on Turn on the TVWait for the VCR to program channels Press the Menu button. The menu shown below will appearProgramming Channels Press the Number 3 button to select Tuner SET UPPress the VCR button, then press the Menu button to Bring up the main menu displayPress the VCR button Adding/Deleting ChannelsPress the Menu button to bring up the main menu display Press the Number 4 button to select ADD/DELETE CHPress the VCR button, then press the Menu button Setting the ClockPress the Number 3 button to select SET Manual Clock Press the EXIT/STATUS buttonPress the Number 4 button to select SET Time Zone Setting the Clock cont’dTime Zone Selection Manual PBS Channel Selection Automatic PBS Channel Selection Setting the Clock cont’dPress the EXIT/STATUS button to exit Daylight-Saving Time SelectionLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons Stop Button REWind ButtonEject Button JOG/SHUTTLE ButtonDisplay Panel OTR Light Display Panel cont’dRemote Sensor Tape Speed Lights Memory LightFront Panel Rear Panel 2Find the code for your TV 4Repeat step Setting the Remote Control to Operate a TVFind the code for your Cable Box/DSS Receiver Repeat step Cable BOX/DSS Receiver CodesOn-Screen Status Displays Press the Number 2 button to select on Screen ModeCounter will remain on the screen Sound ProgramRemote Locator When you find the remote control, point the remote at1Turn on the TV 2Insert a tape PlayingRead and follow the steps below to play a tape Appear on the display panel RecordingStopping an OTR One Touch RecordingStarting an OTR Recording One Channel/Watching Another Press the Number 1 button to select Program Timer RecordingSelect a once, daily, or weekly recording RecordingFollow to set the recording’s stop time Instructions continue onBox/DSS Receiver on Tape Speeds Timer Recording cont’dChecking or Clearing Timer Recordings Local TV Stations Call letters Setting Up the VCR Plus+ Programming SystemTV Channels Cable Channels Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Cable Box or DSS Receiver Controller Connecting the ControllerPress the Number 5 button to select SET Cable BOX Setting the Controller to Operate a Cable BoxPress the Menu button. Wait for a few seconds Ton. When the Cable Box changes to channel 09, go to stepNumber 2 button to select NO. Use the Number buttons to Press the Menu button or the EXIT/STATUS buttonController to on Press the Number 6 button to select SET DSS ReceiverPress the Number 1 button to set the DSS Receiver Press the Number 1 button to select YES Press the Menu buttonAudio cables Rerecording Tape DuplicationVideo cable VCR 1 will play your tape. Insert a prerecorded tape in VCRInsert a tape Index SearchReceiving a Second Audio Program Multi-Channel Television Sound SystemReceiving a Stereo Broadcast Press the Number 1 button so that on appears beside Multi-Channel Television Sound System cont’dHi-Fi Stereo Tape Playback Tape Counter Memory Using the Tape CounterBegin tape playback To bring up the Goto displayStop the tape Turn off VCRRepeat Playback Video Stabilizer Video StabilizerForward and Reverse Searching Playback OptionsViewing a Still Picture Viewing a Slow Motion PictureAutomatic Operation Features Cable Box/DSS Receiver Output Channel channel 03 or GlossarySpecifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories