Philips VRX463 warranty Press the Menu button, Press the Number 1 button to select YES

Page 46

46 Setting the Controller to Operate a DSS Receiver (cont’d)

6

Press the MENU button.

SELECT OUTPUT CH

 

 

 

OF YOUR DSS RECEIVER

CBL/DSS

VCR

TV

 

0-

 

 

 

 

PAUSE/STILL

POWER

MUTE

TO END PUSH EXIT

 

PLAY

 

7

REW

FF

 

EJECT

 

F.ADV

6

A zero will appear in the SELECT OUTPUT CH menu. Press one Number button (3 or 4) to complete the out- put channel of your DSS Receiver (channel 03 or 04).

•Press 0 if you connected the VIDEO/AUDIO OUT Jacks of the DSS Receiver to the VCR’s VIDEO/AUDIO IN Jacks. A/V will appear on-screen as the output channel. A/V CONNECT A/V REAR ONLY will appear.

•If you make a mistake, press the CLEAR button, then enter the correct output channel.

STOP

VCR PLUS+/ENTER

EXIT/STATUSCLEAR

 

MENU

VOL

JOG/SHUTTLE

CHANNEL

 

8

10

SELECT OUTPUT CH

OF YOUR DSS RECEIVER

03

TO CONTINUE PUSH MENU

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

8

Press the MENU button.

9

11

4

5

6

 

1

2

3

 

7

8

9

 

100

0

GO-TO

REC /OTR

INDEX

MEMO

 

VAR.

 

 

SLOW

 

SPEED

VCR/TV SLOW

TRACKING SKIP

 

 

SEARCH

7

9

A four will appear in the menu. Use the Number buttons to enter the second digit of the two-digit code for your DSS Receiver. (See the list on page 44.)

SELECT CODE NUMBER OF YOUR DSS RECEIVER

42

TO TEST PUSH MENU

DID DSS RECEIVER

CHANGE TO CHANNEL 205?

1 YES 2 NO

TO END PUSH EXIT

10

Press the MENU button. Wait for the DSS Receiver to change to channel 205. When it does, go to step 11.

•If the DSS Receiver does not change to channel 205, press the Number 2 button to select NO. Repeat steps 9 - 10. If the DSS Receiver doesn’t change to channel 205, the Controller will not operate your DSS Receiver. Press the EXIT/STATUS button.

11

Press the Number 1 button to select YES.

“DSS RECEIVER CONTROL IS ON” will appear for five seconds. The screen will return to the program you were watching.

REMOTE LOCATOR

Helpful Hints

•If your DSS Receiver does not respond to the code in steps 9 - 10, the Controller will not change chan- nels at the DSS Receiver during a timer recording. In this case, you must select the channel to be recorded at the DSS Receiver before a timer recording begins. Enter the DSS Receiver output channel (03 or

04)at step 5 on page 35. Leave the DSS Receiver on for the timer recording. Details are on page eight.

•If more than one code is listed for your brand of DSS Receiver, try all of the codes at steps 9 - 10 before you determine the Controller will not change the VCR channels.

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Video Cassette Recorder VRX463 Dear Philips Magnavox product owner For Customer UseSafety Precautions FeaturesIntroduction Table of Contents Using the Remote Control Before Using Your VCRPutting Batteries in the Remote Control VCR MaintenanceHookups Without a Cable Box Disconnect the antenna or cable from your TVHookups Without a Cable Box cont’d Antenna Or CableRecording or Viewing a Scrambled or Unscrambled Channel Timer RecordingsHookups With a Cable Box/DSS Receiver Watching TV With the VCR Turned OffPlaying a Tape Hookups With a Cable Box/DSS Receiver cont’dRecording One Channel/Watching Another Antenna in Jack On back of TVVCR will come on Press the VCR button, then press the Power buttonTurning on Your VCR Turn on the TVPress the Menu button. The menu shown below will appear Wait for the VCR to program channelsPress the VCR button, then press the Menu button to Press the Number 3 button to select Tuner SET UPProgramming Channels Bring up the main menu displayPress the Menu button to bring up the main menu display Adding/Deleting ChannelsPress the VCR button Press the Number 4 button to select ADD/DELETE CHPress the Number 3 button to select SET Manual Clock Setting the ClockPress the VCR button, then press the Menu button Press the EXIT/STATUS buttonTime Zone Selection Setting the Clock cont’dPress the Number 4 button to select SET Time Zone Manual PBS Channel Selection Setting the Clock cont’d Automatic PBS Channel SelectionDaylight-Saving Time Selection Press the EXIT/STATUS button to exitLanguage Selection Press the Number 2 button to select VCR SET UPLanguage Selection Press the Number 3 button to select LanguageRemote Control Buttons Eject Button REWind ButtonStop Button JOG/SHUTTLE ButtonDisplay Panel Remote Sensor Display Panel cont’dOTR Light Tape Speed Lights Memory LightFront Panel Rear Panel Setting the Remote Control to Operate a TV 2Find the code for your TV 4Repeat stepCable BOX/DSS Receiver Codes Find the code for your Cable Box/DSS Receiver Repeat stepCounter will remain on the screen Press the Number 2 button to select on Screen ModeOn-Screen Status Displays Sound ProgramWhen you find the remote control, point the remote at Remote LocatorRead and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape Recording Appear on the display panelStarting an OTR One Touch RecordingStopping an OTR Recording One Channel/Watching Another Select a once, daily, or weekly recording Timer RecordingPress the Number 1 button to select Program RecordingBox/DSS Receiver on Instructions continue onFollow to set the recording’s stop time Timer Recording cont’d Tape SpeedsChecking or Clearing Timer Recordings TV Channels Cable Channels Setting Up the VCR Plus+ Programming SystemLocal TV Stations Call letters Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Press the EXIT/STATUS button. Program WAS COM Connecting the Controller Cable Box or DSS Receiver ControllerSetting the Controller to Operate a Cable Box Press the Number 5 button to select SET Cable BOXNumber 2 button to select NO. Use the Number buttons to Ton. When the Cable Box changes to channel 09, go to stepPress the Menu button. Wait for a few seconds Press the Menu button or the EXIT/STATUS buttonPress the Number 1 button to set the DSS Receiver Press the Number 6 button to select SET DSS ReceiverController to on Press the Menu button Press the Number 1 button to select YESVideo cable Rerecording Tape DuplicationAudio cables VCR 1 will play your tape. Insert a prerecorded tape in VCRIndex Search Insert a tapeReceiving a Stereo Broadcast Multi-Channel Television Sound SystemReceiving a Second Audio Program Multi-Channel Television Sound System cont’d Press the Number 1 button so that on appears besideHi-Fi Stereo Tape Playback Using the Tape Counter Tape Counter MemoryStop the tape To bring up the Goto displayBegin tape playback Turn off VCRRepeat Playback Video Stabilizer Video StabilizerViewing a Still Picture Playback OptionsForward and Reverse Searching Viewing a Slow Motion PictureAutomatic Operation Features Glossary Cable Box/DSS Receiver Output Channel channel 03 orSpecifications Helpful Hints Helpful Hints cont’d Renewed Index Supplied Accessories
Top Page Image Contents