Linear VS-GSWG manual Indicator Descriptions, Apex Function Display Indications

Indicator Descriptions

INDICATOR DEFINITION

OPERATION PROGRAMMING

INDICATION WHEN LIT

DURING NORMAL OPERATION

INDICATION WHEN LIT

DURING PROGRAMMING

24 VOLT INPUT		LOW VOLTAGE AC POWER IS PRESENT
POWER
24 VOLT DC		LOW VOLTAGE DC POWER IS PRESENT
ACCY POWER
		OPEN SIGNAL PRESENT FROM THE INTERNAL
OPEN		RECEIVER OR AN EXTERNAL DEVICE
		CONNECTED TO THE OPEN INPUT TERMINAL
CLOSE		CLOSE SIGNAL IS PRESENT FROM A DEVICE
		CONNECTED TO THE CLOSE INPUT TERMINAL
STOP		STOP INPUT TERMINAL IS OPEN AND
		NOT CONNECTED TO COMMON
PROGRAM			CONTROLLER IS IN PROGRAMMING MODE
REVERSE	DELAY SET	SIGNAL FROM REVERSING DEVICE IS PRESENT	SET REVERSE DELAY TIME
LOCKOUT	ALARM SET	CONTROLS AND OPERATOR ARE LOCKED OUT	SET RUN ALARM AND PRE-START ALARM
		BECAUSE OF EXISTING TROUBLE CONDITION
RADIO	LEARN	BUILT-IN RECEIVER IS DETECTING A RADIO	TRANSMITTERS CAN BE ENTERED INTO
		SIGNAL FROM A REMOTE CONTROL	MEMORY (UP TO 40 TRANSMITTERS)
OPEN CURRENT	SET	MOTOR CURRENT HAS EXCEEDED THE	SET MAXIMUM OPEN CURRENT
		OPEN CURRENT SETTING WHILE OPENING
		OPEN OBSTRUCTION TERMINAL CONNECTED
OPEN OBSTR	MGT 2 SET	TO COMMON BY BEAM OR SAFETY EDGE, OR	SET MGT #2 FUNCTION
		SIGNAL FROM MGT OBSTACLE TRANSMITTER
OPEN RELAY	LH/RH SET	OPEN RELAY IS ACTIVATED	SET LEFT-HAND RIGHT-HAND OPERATION
OPEN LIMIT	BRAKE DELAY	OPEN LIMIT SWITCH IS ACTIVATED
CLOSE CURRENT	SET	MOTOR CURRENT HAS EXCEEDED THE	SET MAXIMUM CLOSE CURRENT
		CLOSE CURRENT SETTING WHILE CLOSING
		CLOSE OBSTRUCTION TERMINAL CONNECTED
CLOSE OBSTR	MGT 1 SET	TO COMMON BY BEAM OR SAFETY EDGE, OR	SET MGT #1 FUNCTION
		SIGNAL FROM MGT OBSTACLE TRANSMITTER
CLOSE RELAY	AUTO CLOSE SET	CLOSE RELAY IS ACTIVATED	SET AUTO-CLOSE TIME
CLOSE LIMIT	AC DC SET	CLOSE LIMIT SWITCH IS ACTIVATED	SET MOTOR TYPE
SINGLE	SET	SINGLE TERMINAL CONNECTED TO COMMON	SET SINGLE BUTTON INPUT FUNCTION
		BY AN EXTERNAL PUSHBUTTON OR RADIO
MAX RUN	SET	MAXIMUM RUN TIMER HAS BEEN EXCEEDED	SET MAXIMUM RUN TIME
COMM LINK	SET	DUAL OPERATOR CONNECTION DETECTED,
		BLINKS IF CONNECTION HAS FAILED
MAINT ALERT	SET	MAINTENANCE IS REQUIRED ON OPERATOR	SET MAINTENANCE ALERT CYCLE COUNT

APEX FUNCTION DISPLAY INDICATIONS

"RL"

"PM"

"AC"

"RP"

"OC"

"CC"

"AD"

LEFT OR RIGHT HAND OPERATION

SINGLE OR

DUAL GATE

AUTO CLOSE

TIMER

RUN ALARM

PRE-START ALARM

MAXIMUM OPEN CURRENT

MAXIMUM CLOSE CURRENT

ADVANCED

PROGRAMMING

"RT"

"SB"

"SM"

"ST"

"AR"

"RD"

"BD"

MAXIMUM

RUN TIMER

SINGLE BUTTON INPUT SETUP

STAGGER

MODE

STAGGER

TIME

AUXILIARY

RELAY MODE

REVERSE

DELAY TIME

BRAKE

DELAY TIME

"CP"

"SP"

"CT"

"MA"

"MT"

"AT"

"RA"

CONSTANT

PRESSURE MODE

SHADOW LOOP

OPEN INHIBIT

RESET CYCLE

COUNT

MAINTENANCE ALERT TRIGGER

MID-TRAVEL

STOP POSITION

ANTI-TAILGATE

ENABLE

RADIO

ENABLE

LEARN

"TL" TRANSMITTERS

DELETE

"TD" TRANSMITTERS

LEARN MGT

"ML" TRANSMITTERS

ERASE MGT

"MD" TRANSMITTERS

MOTOR TYPE

"MO" SELECTION

RESET TO

"CL" FACTORY DEFAULTS

VS-GSWG Swing Gate Operator Installation Guide - 9 - P1250 Revision X6 7-8-2011