Linear VS-GSWG Dual Gate Installations, Optional In-Cabinet Heater, Open and Close Limit settings

Page 23

Dual Gate Installations

Two operators can be used in dual gate installations. The operators communicate with each other through the 3-wire COMM LINK terminals.

When one operator activates, the COMM LINK connection signals the other operator to activate. Each operator functions independently, controlling its gate and monitoring its inputs and accessories.

A three-wire shielded conductor cable is required to connect two operators together for dual operation. Use Belden 8760 Twisted Pair Shielded Cable (or equivalent) only – P/N 2500-1982, per foot).

✓NOTE: The shield wire should be connected COMM LINK terminal “C” in both operators.

Three of the programming functions available are only used for dual gate installations:

•Dual Gate Enable

Dual Gate Enable must be set for all dual gate installations.

•Stagger Mode

The Stagger Mode function determines if the operator has a delayed open or a delayed close. In dual swing gate installations, typically one operator is programmed for delayed open, and the other operator is programmed for delayed close.

•Stagger Delay Time

The Stagger Time sets the length of the delay for the Stagger Mode.

See Pages 12 & 14 for details on these three dual gate programming functions.

Set the following parameters in each gate operator individually in a single gate mode before connecting the network cable and operating in dual gate mode.

1.Open and Close Limit settings

2.Open and Closed direction inherent entrapment protection (OC & CC)

After these parameters have been set, and each operator has been tested independently and is functioning correctly in single gate mode, then set BOTH operators to dual gate (dg) in the Paired Mode setup step under Basic Programming steps.

DUAL GATE

 

 

 

 

OPERATOR #1

COMM LINK

 

 

 

 

SHIELD

 

 

 

 

 

 

 

WIRING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Optional In-Cabinet Heater

The operator can be ordered with an optional cold weather package that includes an in-cabinet heater to keep the drive train and electronics warm in cold environments.

In-cabinet heaters can also be ordered separately and should be wired to the operator as shown in Figure 14 Contact Technical Services for heater wiring information for a specific voltage and phase of operator.

SINGLE PHASE 115V, 208V, & 230V MODELS (All heaters have built-in switch and thermostat)

BLACK

 

POWER BOX

WHITE

 

115 VOLT HEATER (P/N 2510-262)

CONNECT TO LEADS LABELED

 

208/230 VOLT HEATER (P/N 2510-273)

"ACCESSORY POWER CONNECTION"

 

 

 

 

THREE PHASE 208V & 230V MODELS

208/230 VOLT HEATER (P/N 2510-273)

CONTACTOR

 

 

 

THREE PHASE 460V MODELS

CONTACTOR

460 VOLT HEATER (P/N 2510-354)

Figure 14. In-cabinet Heater Wiring

CONNECT

C - C

B - B

A - A

USE BELDEN 8760 TWISTED PAIR SHIELDED CABLE OR EQUIVALENT

CONNECT SHIELD WIRE AT BOTH ENDS

OPERATOR #2

SHIELD

Figure 13. COMM LINK Wiring

VS-GSWG Swing Gate Operator Installation Guide

- 21 -

P1250 Revision X6 7-8-2011

 

Page 22 Page 24
Image 23
Page 22 Page 24
Contents VS-GSWG Table of Contents Safety Information and Warnings Pre-installation InformationDC Control and Accessory Wiring Wiring SpecificationsAC Power Wiring Mounting Specifications Mounting Pad InstallationGate Preparation Operator Preparation Gate Arm InstallationVent Plug Installation Gate Arm AssemblyEarth Ground Operator SetupController Access AC Power ConnectionSetting Speeds using LSO-2 & LSC-2 Open and Close Limit AdjustmentLimit Nuts Rough Adjustment Limit Nuts Fine AdjustmentLoosen the set screw on the adjustment nut Torque Limiter AdjustmentButtons Controller FeaturesApex Function Display Indications Indicator DescriptionsTerminal Group Function Terminal DescriptionsOperator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Maximum Close Direction Current Setting Run Alarm and Pre-start AlarmMaximum Open Direction Current Setting Advanced Controller Programming Constant Pressure Mode Auxiliary Relay ModeReverse Delay Time Brake Delay TimeRadio Enable Reset Cycle CountMaintenance Alert Trigger Anti-tailgate EnableMGT Obstacle Transmitter Learn Reset Controller to Factory DefaultsRadio Transmitter Learn Radio Transmitter DeleteLoop Layout Illustration Safety Edge Layout Illustration Photoeye Installation Illustration Optional In-Cabinet Heater Dual Gate InstallationsOpen and Close Limit settings Operation Indications Gate OperationMGT Obstacle Transmitter Trouble Error IndicationsEntrapment Comm Link Connection FailureTroubleshooting General Preventative MaintenanceMonth Preventative Maintenance FCC NoticeModel VS-GSWG Exploded View Model SWG Mechanical Parts List Variable Speed Control Box Assemblies Controller Parts ListProgramming the Hitachi Inverter Variable Speed Drive ProgrammingShown for Clarity only not Included in ARM Assembly Gate Arm Assembly Parts ListThis page left blank intentionally Gate Operator Installation Checklist
Top Page Image Contents