Linear VS-GSWG Radio Transmitter Learn, Radio Transmitter Delete, MGT Obstacle Transmitter Learn

Advanced Controller Programming (Cont.)

Radio Transmitter Learn

The Controller’s built-in MegaCode® radio receiver can store the IDs of up to 40 transmitters. Refer to the fi gure for the steps required to learn transmitters.

✓NOTE: This function will NOT be displayed if the transmitter memory is full, or if the radio receiver is disabled.

Radio Transmitter Delete

Transmitters can be deleted from the Controller’s memory either individually, or all at the same time. Refer to the fi gure for the steps required to delete transmitters.

FUNCTION

"TL"

LEARN

TRANSMITTERS

ENTER	PRESS ENTER (ONCE FOR EACH TRANSMITTER,
	UP TO 40 TRANSMITTERS TOTAL)

"TL" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS READY TO LEARN A TRANSMITTER

ACTIVATE THE TRANSMITTER

DISPLAY WILL SHOW "- -" THEN THE

TRANSMITTER ID NUMBER - IF TRANSMITTER

IS ALREADY ENTERED, "dU" WILL BE DISPLAYED, IF DECODE IS BAD "ERROR" WILL BE DISPLAYED

✓NOTE: This function will NOT be displayed if no transmitters are stored in memory, or if the radio receiver is disabled.

MGT Obstacle Transmitter Learn

The Controller supports one or two Model MGT Obstacle Transmitters. The transmitters can be programmed to function as Open Obstruction, Close Obstruction, Reverse, or Stop. Refer to the fi gure for the steps required to learn MGT transmitters.

✓NOTE: This function will NOT be displayed if two MGT transmitters are already stored in memory, or if the radio receiver is disabled.

FUNCTION

		"TD"		ENTER	PRESS ENTER
					"TD" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER
					IS READY TO DELETE ONE OR MORE TRANSMITTERS,
					(TO EXIT WITHOUT DELETING ANY, PRESS ENTER)
				ENTER	TO DELETE ALL TRANSMITTERS, PRESS ENTER FOR
					2 SECONDS, OR TO PICK TRANSMITTERS GO TO NEXT STEP
					PRESS UP OR DOWN TO SCROLL THROUGH THE LIST
			UP OR DOWN
					OF TRANSMITTER ID NUMBERS
					THE TRANSMITTER ID NUMBER IS DISPLAYED
					(TO EXIT WITHOUT DELETING, PRESS ENTER)
					(TO PICK A DIFFERENT TRANSMITTER ID, PRESS UP OR DOWN)
	DELETE				PRESS ENTER FOR 2 SECONDS TO DELETE THE
				ENTER
TRANSMITTERS
					TRANSMITTER DISPLAYED

MGT Obstacle Transmitter Delete

MGT transmitters can be deleted from the Controller’s memory either individually, or all at the same time. Refer to the fi gure for the steps required to delete MGT transmitters.

✓NOTE: This function will NOT be displayed if no MGT transmitters are stored in memory, or if the radio receiver is disabled.

Motor Type Selection

The factory sets the default for the Controller to match the type of motor in the operator. If required, change the motor selection option to a different type of motor used in the operator. The options available are:

FUNCTION

ENTER

"ML"

UP OR DOWN

ENTER

LEARN MGT

TRANSMITTERS

PRESS ENTER, "ML" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER IS READY TO LEARN AN MGT TRANSMITTER

ACTIVATE THE MGT TRANSMITTER, THE DISPLAY WILL FLASH "rE" - IF THE TRANSMITTER IS ALREADY ENTERED,

"DU" WILL BE DISPLAYED, IF DECODE IS BAD "ERROR" WILL BE DISPLAYED

PRESS UP OR DOWN TO SELECT THE MGT FUNCTION: "rE" = REVERSE "St" = STOP

"OP" = OPEN OBSTRUCTION "CL" = CLOSE OBSTRUCTION

PRESS ENTER TO ACCEPT THE SELECTION

DISPLAY WILL SHOW "--" FOR 5 SECONDS, THEN SHOW THE TRANSMITTER'S ID NUMBER - REPEAT STEPS FOR SECOND MGT TRANSMITTER IF USED

•AC Motor Only

•DC Motor Only with Mechanical Braking

•DC Motor with Electronic Soft Start/Stop

•3 Phase AC Motor

•AC Motor with DC Motor Backup with Mechanical Braking

•AC Motor with DC Motor Backup with Electronic Soft Start/Stop

Reset Controller to Factory Defaults

The Controller can be reset with this function. ALL PROGRAMMED DATA WILL BE LOST, and the factory defaults will be loaded. This function will not erase radio transmitters, current sense values, or motor type. Transmitters must be deleted with the two functions above.

FUNCTION

	ENTER	PRESS ENTER
"MD"
		"MD" WILL BLINK FOR 30 SECONDS WHILE THE CONTROLLER
		IS READY TO DELETE ALL MGT TRANSMITTERS

TO DELETE ALL MGT TRANSMITTERS, PRESS ENTER FOR

ENTER 2 SECONDS, (TO EXIT WITHOUT DELETING ANY, QUICKLY

PRESS ENTER)

ERASE MGT	THE DISPLAY WILL SHOW "DELETE ALL" AND THE
TRANSMITTERS	CONTROLLER RETURNS TO PROGRAMMING MODE

FUNCTION

"CL" ENTER WHILE "CL" IS DISPLAYED, PRESS ENTER

ALL PROGRAMMED DATA WILL BE CLEARED

AND THE FACTORY DEFAULTS WILL BE

STORED IN MEMORY.

NOTE: THIS FUNCTION WILL NOT ERASE

TRANSMITTERS, CURRENT SENSE VALUES,

OR MOTOR TYPE.

RESET TO

FACTORY DEFAULTS

FUNCTIONOPTIONS

"MO"

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

MOTOR TYPE

SELECTION

AC MOTOR ONLY

DC MOTOR ONLY WITH BRAKING

DC MOTOR WITH SOFT START/STOP

NOTE: SELECTION

3 PHASE AC MOTOR MUST MATCH

MOTOR BOARD!

AC MOTOR PRIMARY WITH

DC MOTOR BACKUP WITH BRAKING

AC MOTOR PRIMARY WITH

DC MOTOR BACKUP WITH SOFT START/STOP

VS-GSWG Swing Gate Operator Installation Guide - 17 - P1250 Revision X6 7-8-2011