Linear VS-GSWG manual Advanced Controller Programming

Page 16

Advanced Controller Programming

Entering Advanced Programming Mode

To access and program the Advanced Programming functions, for each programming session, Advanced Programming must be enabled.

After exiting programming, the Advanced Programming functions will be available on the programming display during the next programming session unless the operator has run 50 or more cycles. After that, Advanced Programming must be enabled again.

Maximum Run Time

The factory default for the Maximum Run Time (MRT) is 99 seconds. When the operator starts, a timer will begin counting. If a open or close limit is not reached or an obstacle or reversing input is not received

FUNCTION

"AD"

ADVANCED

PROGRAMMING

OPTIONS

ADVANCED PROGRAMMING FUNCTIONS

WILL NOT BE DISPLAYED

ADVANCED PROGRAMMING OPTIONS

WILL BE DISPLAYED

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS NOTE: ADVANCED PROGRAMMING

WILL STAY ENABLED AFTER

PRESS ENTER TO EXITING PROGRAMMING UNTIL

SELECT AN OPTION THE GATE CYCLES 50 TIMES

before the timer expires, the operator will stop, the unit locks out and the alarm sounds. The timer can be set for 10 to 99 seconds, but should be left at 99 in most applications. Setting it too close to the actual run time may cause the time to expire with changing ambient temperature, gate conditions, etc…

If AC is present and an open or close limit is not reached or an obstacle or reversing input is not received before this timer exceeds MRT, the operator will stop, the unit locks out and the alarm sounds.

Single Button Input Setup

 

FUNCTION

 

OPTIONS

 

 

 

 

"RT"

 

 

 

DISPLAY SHOWS CURRENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAXIMUM RUN TIME SETTING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ENTER PRESS ENTER FOR 1 SECOND

 

 

 

 

 

 

 

 

WHILE DISPLAY IS FLASHING, PRESS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UP OR DOWN TO CHANGE THE

 

 

 

 

 

 

 

 

MAXIMUM RUN TIME (10-99 SECONDS)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAXIMUM RUN

 

ENTER PRESS ENTER TO STORE THE VALUE

 

 

TIMER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This function is used for selecting the operation for single button controls and radio receivers.

The factory default sets the SINGLE input terminal so successive inputs will cycle the operator in OPEN-STOP-CLOSE-STOP order.

Alternately, the SINGLE input can be set to cause the gate to OPEN unless the gate is fully open. If the gate is fully open, the input will cause the gate to CLOSE.

Stagger Mode

This function is used in dual gate installations only. The factory default sets the Stagger Mode to OFF. In dual gate installations the two operators communicate through the 3-wireCOMM LINK interface. When using the Stagger Mode, set one operator for delayed opening and

FUNCTION

"SB"

SINGLE BUTTON

INPUT SETUP

OPTIONS

SINGLE INPUT WILL CYCLE OPERATOR

IN ORDER OF OPEN-STOP-CLOSE-STOP

SINGLE INPUT WILL OPEN OPERATOR,

IF OPERATOR IS ALREADY OPEN, SINGLE

INPUT WILL CLOSE OPERATOR

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

the other operator for delayed closing. The Stagger Time programming function (see below) sets the length of the delay.

NOTE: This function will only be displayed if dual gate operation is selected.

Stagger Delay Time

This function is used in dual gate installations only. The factory default sets the Stagger Time to 0 seconds (OFF). The Stagger Time

FUNCTION

"SM"

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO SELECT AN OPTION

OPTIONS

DISABLES STAGGER FUNCTION

SETS THIS OPERATOR FOR

DELAYED OPEN

SETS THIS OPERATOR FOR

DELAYED CLOSE

sets the delay for the Stagger Mode. The Stagger Delay Time can be set from 1-99 seconds.

NOTE: This function will only be displayed if dual gate operation is selected.

 

STAGGER

 

 

 

 

 

DUAL GATES

 

 

MODE

 

 

 

 

 

ONLY

 

 

 

 

 

 

FUNCTION

 

OPTIONS

 

 

 

 

 

"ST"

 

 

 

STAGGER TIMER DISABLED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SET STAGGER DELAY VALUE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 TO 99 SECONDS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESS UP OR

 

 

 

 

 

 

DOWN TO CYCLE

 

 

 

 

 

 

THROUGH OPTIONS

 

 

 

 

 

 

 

 

 

 

STAGGER

PRESS ENTER TO

 

DUAL GATES

 

DELAY TIME

SELECT AN OPTION

 

ONLY

 

 

 

 

 

 

VS-GSWG Swing Gate Operator Installation Guide

- 14 -

P1250 Revision X6 7-8-2011

 

Image 16
Contents VS-GSWG Table of Contents Pre-installation Information Safety Information and WarningsAC Power Wiring Wiring SpecificationsDC Control and Accessory Wiring Gate Preparation Mounting Pad InstallationMounting Specifications Gate Arm Installation Vent Plug InstallationGate Arm Assembly Operator PreparationOperator Setup Controller AccessAC Power Connection Earth GroundOpen and Close Limit Adjustment Limit Nuts Rough AdjustmentLimit Nuts Fine Adjustment Setting Speeds using LSO-2 & LSC-2Torque Limiter Adjustment Loosen the set screw on the adjustment nutController Features ButtonsIndicator Descriptions Apex Function Display IndicationsTerminal Descriptions Terminal Group FunctionOperator Accessory Connections Operator Accessory ConnectionsBasic Controller Programming Maximum Open Direction Current Setting Run Alarm and Pre-start AlarmMaximum Close Direction Current Setting Advanced Controller Programming Auxiliary Relay Mode Reverse Delay TimeBrake Delay Time Constant Pressure ModeReset Cycle Count Maintenance Alert TriggerAnti-tailgate Enable Radio EnableReset Controller to Factory Defaults Radio Transmitter LearnRadio Transmitter Delete MGT Obstacle Transmitter LearnLoop Layout Illustration Safety Edge Layout Illustration Photoeye Installation Illustration Open and Close Limit settings Dual Gate InstallationsOptional In-Cabinet Heater Gate Operation Operation IndicationsError Indications EntrapmentComm Link Connection Failure MGT Obstacle Transmitter TroubleTroubleshooting Preventative Maintenance Month Preventative MaintenanceFCC Notice GeneralModel VS-GSWG Exploded View Model SWG Mechanical Parts List Controller Parts List Variable Speed Control Box AssembliesVariable Speed Drive Programming Programming the Hitachi InverterGate Arm Assembly Parts List Shown for Clarity only not Included in ARM AssemblyThis page left blank intentionally Gate Operator Installation Checklist