GTO GP-SW050 owner manual Connecting Power to the Operator, Not provided

Page 16

Connecting Power to the Operator

1.Turn the breaker power switch off before connecting AC power. Have a licensed electrician run 115 Vac wiring into the Field Wiring Connection Compartment. The 115 Vac line will power the gate operator system. The circuit must be protected with a 15 A main disconnect breaker

(not provided).

NOTE: Power and wiring connections MUST be performed by a licensed electrician in accordance with NEC (National Electric Code) and local codes.

NEVER run low voltage (e.g., accessory or receiver) wires in conduit containing 115 Vac wiring.

2.Connect batteries to operator as shown. The red wire connects to the positive terminal in the control box. The black wire connects to the negative terminal in the control box. The jumper wire (included) connects both batteries together with the remaining terminals. Wire the 24V system in series as shown below.

3.Turn on AC power at this time.

RED WIRE to positive (+)

JUMPER WIRE (Supplied) negative (-) to positive (+)

NOTE: Battery should be a 12 Vdc, U1, 230 Amp Minimum, Lead Acid Battery (Typical Lawn and Tractor Battery).

BLACK WIRE to negative (–)

NOTE: When first turning operator power switch on, the unit may beep once

every 5 seconds until the new batteries can be fully charged (30-60 minutes charging time).

13

Page 15 Page 17
Image 16
Page 15 Page 17
Contents GP-SW050 Conversion Chart Vehicular gate operator class categoriesTable of Contents Important Safety Instructions for the System Designer Before Installation III. After InstallationMeans of Protection Against Entrapment Important Safety Instructions for the Consumer/End User Required Safety Precautions for Gates Entrapment ProtectionMoving Gate Can Cause Injury Or Death Technical Specifications MotorParts Identification Operator ChassisInstalling the Gate Operator Preparation of the GateUsing the Mounting Template Before mounting the operator, check the followingTemplateMounting Removing the Operator Housing Mounting the OperatorConnecting Power to the Operator Not providedGate Arm Connection Overview Right Mounted ArmConnecting the Gate Arm to the Gate Install the key into the output shaft. FigControl Board Description ExitSetting the Limits Open Limit SettingStall Force and Auto-Close Adjustments Stall Force AdjustmentDIP Switch Settings DIP #1 Open DirectionInput Connections GTO Loop Detector Button Station Accessory Terminal ConnectionsSiren-Activated Entry Device Output Connections Lock COM and Lock N.O. / Lock N.C. Lock relay outputAccessory Power Supply Connection 12Vdc @ 300 mA Power SupplyWiring a 3-button station Prison Mode Operation Class IV ApplicationsReinstalling the Operator Housing Installing a Dual Gate Operator System Dual Gate Link ConnectionSetting Dual Gate Sequence Slave DIP Switch SettingsOverview of a Dual Gate Operator Installation Slave OperatorMaintenance Maintenance ScheduleTroubleShooting Guide GP-SW050 Audible FeedbackSafety LED on Cycle LED on brightlyShadow LED on Open Edge LED onClose Edge LED on Open LED on brightlyClose LED on brightly Stop LED on brightlyWarranty and Repair Service Instructions for the Consumer/End UserInstallation of this operator conforms to Class Installation ChecklistW . g t o a c c e s s . c o m

GP-SW050 specifications

The GTO GP-SW050 is a cutting-edge satellite dish that stands out in the realm of satellite communications. Designed for efficiency and durability, this model offers users a robust solution for receiving satellite signals, making it ideal for both residential and commercial applications.

One of the main features of the GTO GP-SW050 is its advanced materials construction. The dish is crafted from high-quality, weather-resistant materials that ensure longevity even in harsh environmental conditions. The reflective surface of the dish is engineered to maximize signal reception, enhancing the clarity and reliability of the transmitted data.

In terms of technology, the GTO GP-SW050 employs a unique multi-band reception capability. This allows it to operate across different frequency bands, making it versatile for various satellite services. Users can enjoy seamless access to television, internet, and data services without the need for multiple dishes.

The design of the GTO GP-SW050 emphasizes ease of installation and use. The dish features a lightweight structure, which simplifies the mounting process and reduces the overall installation time. Additionally, the adjustable mounting bracket allows for precise alignment, ensuring optimal signal reception.

Another significant characteristic of the GTO GP-SW050 is its compatibility with various satellite systems. Whether you are subscribing to local or international satellite providers, this dish can be tailored to meet specific service requirements. Its broad compatibility spans multiple satellite networks, making it a future-proof solution in a rapidly advancing technology landscape.

Moreover, the GTO GP-SW050 is equipped with advanced signal processing capabilities. This includes features that enhance signal strength and reduce interference, providing users with a stable connection even in areas more prone to signal disruptions.

When considering power consumption, the GTO GP-SW050 is designed for efficiency, minimizing energy use while maximizing performance. This emphasis on sustainability makes it not only a smart investment but also an environmentally-conscious choice.

In conclusion, the GTO GP-SW050 represents a blend of reliability, performance, and innovation. With its advanced features, durable construction, and versatile technology, it is an excellent choice for individuals looking to enhance their satellite communication experience. Its user-friendly design further reinforces its position as a top choice for both casual users and tech-savvy professionals.
Top Page Image Contents