DIP Switch Settings
MODE 1 & MODE 2:
•Reserved for future features
DIP #1: OPEN DIRECTION 
•OFF: for gate that opens to the left, closes to the right.
•ON: for gate that opens to the right, closes to the left.
DIP #2: SLAVE OPEN SEQUENCE (dual gate installation only) 
• NOTE: This DIP switch is applicable if and only if all the following conditions are valid:
• DIP switch #3 is OFF (Master mode)
•Dual Link cable is connected.
•Slave mode is detected from the second board (DIP switch #3 of the second board is ON)
•If the above conditions are not met, the board will default to single gate operation. If DIP #3 is OFF (Master)
•OFF: Slave gate will open after the master gate.
•ON: Slave gate will open simultaneously with the master gate.
1 |
|
|
|
|
| ON |
| |
|
|
|
|
|
| |||
|
|
|
|
|
| |||
2 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
3 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
4 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
OFF |
|
|
|
|
|
| ON | |
|
|
|
|
|
| |||
DIP #3: MASTER/SLAVE (applicable to dual gate installation only) 
•NOTE: This DIP switch is applicable if and only if all the following conditions are valid:
•Dual Link cable is connected.
•The second operator is detected by the master.
•If the above conditions are not met, the board will default to single mode operation. If DIP #3 is OFF (Master)
•OFF: Master mode operation in dual gate installation if slave setting is detected from the other board.
•ON: Slave mode operation in dual gate installation if master setting is detected from the other board. Control board is non- functional if master operator is not detected.
DIP #4: FAIL SAFE/FAIL SECURE OPERATION 
•OFF: Fail safe mode
When low battery and no AC power conditions are detected the gate will automatically run to the opened position. The gate will remain at the open position until AC power is restored and the battery reaches an acceptable charge level.
•ON: Fail secure mode
When low battery is detected and no AC power is present, the gate will automatically run to the closed position. Gate will auto close only if auto close feature is enabled and gate is at open limit. The gateRUN will1 Y remain at the closedLED10 position until AC
RUN 2 OUTPUTS battery reaches an 
acceptable charge level. CLOSED 
power is restored and the
These switches are for dual gate applications only. See page 26 for dual gate settings.
PORT
OPTIONS
CLOSED 1 | LED09 |
| |
CLOSED 2 |
|
CYCLE | CYCLE |
SAFETY | SAFETY |
SHADOW | SHADOW |
LOOP |
|
OPEN EDGE | OPEN |
EDGE | |
| 19 |
OFF |
|
|
|
| ON |
OFF |
|
|
|
| ON |
<<< | 1 |
|
| ON | >>> |
DELAY |
|
| SIMUL | ||
2 |
|
|
| ||
|
|
| |||
|
|
| |||
MASTER | 3 4 |
|
|
| SLAVE |
|
|
| |||
|
|
| |||
SAFE |
|
|
| SECURE | |
|
|
| |||
|
|
| |||
|
|
| |||
|
|
|
|
|
|
STALL FORCE ADJUST
<<<>>>
MODE 1
MODE 2
OPEN DIR.
SLV OPN DUAL MODE LOW BATT
AUTO CLOSE
TIMER