Yamaha RX-V561 Setting the speaker impedance, 13 En, Before connecting to the Speakers Terminal

Page 17

■Before connecting to the SPEAKERS

terminal

A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridges.

Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable to the “–” (black) terminals.

Remove approximately 10 mm (3/8”) of insulation from the end of each speaker cable and then twist the bare wires of the cable together to prevent short circuits.

10 mm (3/8”)

■Connecting to the SPEAKERS terminals

2

1	Red: positive (+)
	Red: positive (+)
	Black: negative (–)
	3

1Loosen the knob.

2Insert the bare end of the speaker wire into the hole on the terminal.

3Tighten the knob to secure the wire.

Connecting the banana plug

The banana plug is a single-pole electrical connector widely used to terminate speaker cables. First, tighten the knob and then insert the banana plug connector into the end of the corresponding terminal.

Banana plug

Connections

Setting the speaker impedance

Caution

If you are to use 6 ohm speakers, set “SP IMP.” to “6Ω MIN” as follows BEFORE using this unit.

1Make sure this unit is turned off.

See page 21 for details about turning on or off this unit.

2Press and hold 0TONE CONTROL and then press 1STANDBY/ON to turn on this

unit.

This unit turns on, an the advanced setup menu appears in the front panel display.

3Press APROGRAM l / h repeatedly to select “SP IMP.”.

The following display appears in the front panel display.

SP IMP.- 8 MIN

4Press BSTRAIGHT repeatedly to select “6Ω

MIN”.

The following display appears in the front panel display.

SP IMP.- 6 MIN

5Press 1STANDBY/ON to confirm your selection and set this unit to the standby mode.

Note

The setting you made is reflected next time you turn on this unit.

PREPARATION

English

13 En

Image 17

Contents RX-V561 Important safety instructions Example of Antenna Grounding FCC Information for US customersSerial No For Canadian CustomersContents We Want You Listening For a Lifetime FeaturesGetting started Remote controlCheck that you received all of the following parts AM loop antennaEnjoy DVD playback Set up your speakersQuick start guide Center and surround speakers Connect your DVD player and other components See page 20 for the details For further connectionsConnect the FM and AM antennas to this unit Check the type of the connected speakers Using the other Scene buttonsPress Fscene Press Fscene 2 or Scene 2 to select Disc ListeningWhat do you want to do with this unit? Rear panel Connections10 En AC Outlets11 En Placing speakers12 En Connecting speakersRight Left Center Speaker Subwoofer Center speaker Subwoofer Right Left Front speakers aBefore connecting to the Speakers Terminal Setting the speaker impedanceConnecting to the Speakers terminals 13 En14 En Information on jacks and cable plugsAudio jacks Video jacks15 En Information on HdmiHdmi jack and cable plug Hdmi cable plugConnect the video components as follows Connecting video components16 En 17 En Connecting to the HDMI, Component Video or S Video jacksHdmi connection Video monitor Cable TV or Satellite tunerComponent Video connection 18 EnVideo connection Video monitor DVD playerConnecting a CD player and a CD recorder/MD recorder Connecting audio componentsConnecting to the Multi CH Input jacks 19 En20 En Using the Video AUX jacks on the front panelConnecting the FM and AM antennas Turning on and off the power Connecting the power cableSet this unit to the standby mode 21 En22 En Front panel display23 En Using the remote controlInfrared window 30º24 En Optimizing the speaker setting for your listening roomUsing Auto Setup 25 En Press G Enter to return to the Autoresult display 26 EnPress G Enter to confirm your selection Top SET Menu display appears in the OSDIf Warning appears If an error screen appears27 En Selecting the desired Scene template Selecting the Scene templates28 En Selected Scene template is assigned to the buttonWhich Scene template would you like to select? 29 En30 En Preset Scene templates descriptionsCreating your original Scene templates Customizing the preset Scene Templates31 En Renaming the Scene templatesPlayback Quick guide to contentsBasic operations 32 EnAdditional operations Using the Zone B feature33 En Selecting the front speaker setAdjusting speaker levels during Playback Adjusting the tonal quality34 En Enjoying pure hi-fi stereo soundDisplaying signal information Selecting the night listening modePress D AMP and then press Q Menu on the remote control 35 EnUsing the sleep timer Using your headphones36 En Playing video sources BackgroundSound field programs Category Program FeaturesSound field program descriptions 37 EnEnjoying unprocessed input sources Straight decoding mode Enjoying 2-channel sources using Standard decoders38 En PRO LogicEditing sound fields parameters 39 EnAutomatic tuning FM/AM tuningManual tuning Press 5PRESET/TUNING l / h once to begin automatic tuning41 En Automatic preset tuningManual preset tuning Exchanging preset station Selecting preset stationsSee Selecting preset stations on this Press and hold 2PRESET/TUNING for more than 3 secondsPlayback operation Using a USB memory device or a USB portable audio player43 En Supported USB devicesFunction of the play information display 44 EnPress G Enter to play the selected file Playback icon All all repeat, 1 single repeat icons45 En Recording46 En Auto setup Auto SetupManual setup Manual Setup 47 En Using SET MenuSignal information Signal Info 48 En Speaker settings Aspeaker SET49 En Speaker level BSP Level 50 EnSpeaker distance CSP Distance Unit Unit51 En Audio settings Gaudio SETCenter speaker equalizer Dcenter GEQ Low-frequency effect level Elfe LevelInput assignment 52 EnDTS decoder prioritize setting Decoder select mode53 En Rename54 En Multi channel input setupDisplay settings Adisplay SET Parameter initialization DPARAM. INI 55 EnUSB playback styles Eusb Play Style Repeat RepeatUsing remote control on the Scene feature Remote control featuresControlling the input source Components in the Scene mode 56 En57 En Controlling this unit, a TV, or other componentsControlling this unit Controlling a TV AMPControlling other components 58 EnRemote control code default settings Setting remote control codesInput Component Manufacturer Default 59 EnFactory presets Preset Advanced setup60 En Speaker impedance SP IMPProblem Cause Remedy See Troubleshooting61 En General62 En 63 En Problem Cause RemedyError message Cause Remedy See Before Auto Setup64 En Tuner65 En During Auto SetupAfter Auto Setup Status message Cause Remedy 66 EnResetting the system Remote controlAdvanced setup menu appears in the front panel display Press Bstraight repeatedly to select ResetAudio information Glossary68 En Sound field program information 69 EnVideo information MP370 En SpecificationsNumerics Index71 En Headphone 72 EnSpeaker 73 EnFront panel/Face avant Remote control/Boîtier de télécommande Iii List of remote control codes Liste des codes de commandeInternational Manesth TV/VCR Combo TV/DVD/VCR ComboDVD/VCR Combo VCRDVD DVD Recorder DVD/LD ComboDVR LD PlayerRX-V561 Menu Volume