JAI M7+ CL, CV-M7+, M4+ CL CV-M4+command list, Timing and shutter related commands

CV-M4+/M4+CL, CV-M7+/M7+CL

7.5. CV-M4+command list

			Command Name		Format		Parameter		Remarks
		A	–	General settings and	useful commands
EB			Echo Back		EB=[Param.]<CR><LF>		0=Echo off	1=Echo on	Off at power up
ST			Camera Status request		ST?<CR><LF>				Actual setting
HP			Online Help request		HP?<CR><LF>				Command list
VN			Firmware version		VN?<CR><LF>				3 letter version
	B – Timing and shutter related commands
SC			Scanning format		SC=[Param.]<CR><LF>		0=full frame	1=1/2 partial	*1)
							2=1/4 partial	3=1/8 partial
TR			Trigger mode		TR=[Param.]<CR><LF>		0=normal	1=Edge
							2=Pulse width	3=Frame delay
HC			H synchronous accum		HC=[Param.]<CR><LF>		0=H synchr	1= H a-synchr
SM			Shutter mode		SM=[Param.]<CR><LF>		0=Normal	1=Programmab.
SH			Shutter speed		SH=[Param.]<CR><LF>		0=Off (1/24)	1=1/50	All10 steps are
							2=1/100	3=1/200	valid in normal
							4=1/400	5=1/800	trigger mode.
							6=1/1500	7=1/3000
							8=1/5500	9=1/10,000
PE			Programmable expos.		PE= Param. <CR><LF>		0=2.5 H, 1=3.5H	1055=1057.5 H
					[	]			H= 39.3 ∝sec
									Bin. H= 43.3 ∝sec.
BI			Binning		BI=[Param.]<CR><LF>		0=off	1=vertical	*1). Only for SC=0.
									M4+ and M4+CL
SL			Smearless		SL=[Param.]<CR><LF>		0=Off	1=ON	TR=1, 2 or 3
RC			Reset Continuous Trig		RC=[Param.]<CR><LF>		0=Off	1=ON	Only for TR=1
	C – Signals and polarity
SO			Sync on video		SO=[Param.]<CR><LF>		0=no sync on v.	1=sync on v.	Pin #4 on 12 pin
ML			MuLtiple shutter		ML=[Param.]<CR><LF>		0=OFF	1=On	Multi Trig input
									TR=3
SE			Sync/EEN		SE=[Param.]<CR><LF>		0= Sync out	1=EEN out	Pin #9 on 12 pin
FP			FEN/LEN/EEN polarity		FP=[Param.]<CR><LF>		0= active low	1= active high
TP			Trigger polarity		TP=[Param.]<CR><LF>		0= active low	1= active high	*2)
TI			Trigger Input		TI=[Param.]<CR><LF>		0= Hirose 12p	1= LVDS (CL)
	D – Gain and analogue signals setting
GA			Manual gain Level		GA=[Param.]<CR><LF>		0=low	510=high	Range 0 to 510
RP			Rear Potentiometer		RP=[Param.]<CR><LF>		0=manual gain	1=rear potm.
SU			Setup Level		SU=[Param.]<CR><LF>		0=low	255=high	Range 0 to 255
	E – Saving and loading data in EEPROM
LD			Load settings from		LD=[Param.]<CR><LF>		0=Factory data	1=User 1 area	Latest used data
			camera EEPROM				2=User 2 area	3=User 3 area	area becomes
									default at next
									power up
SA			Save settings to		SA=[Param.]<CR><LF>		1=User 1 area	2=User 2 area	Parameter = 0 is
			camera EEPROM				3=User 3 area		not allowed
EA			EEPROM area request		EA?<CR><LF>		0=Factory data	1=User 1 area	Return the used
							3=User 3 area	3=User 3 area	data from area
									*3)

*1) Binning can also be selected by the internal switch SW301.6. Binning has priority over partial scanning. If partial scanning is active when a binning mode is activated, binning will take over and the scanning will be full. The line frequency will be lower in V binning modes (H= 43.3 ∝sec.).

*2) If positive logic is used (TP=1), the first trigger pulse after power up will be ignored.

*3) Data from the latest used data area is loaded as default on power up.

!!Do not try to use commands not shown in the list.

-24 -