JAI TM-1020 operation manual CE Compliance, JAI, Inc

Page 3

Page iii

Notice

The material contained in this manual consists of information that is proprietary to JAI, Inc., and may only be used by the pur- chasers of the product. JAI, Inc. makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein. JAI, Inc. reserves the right to make changes without notice.

Microsoft, Windows 98, Windows 95, Windows NT, and Windows Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Warranty

All of JAI’s solid-state cameras have a full three-year warranty in the United States, and a one-year warranty elsewhere. If any such product proves defective during this warranty period, JAI, Inc. will repair the defective product without charge for parts and labor or will provide a replacement in exchange for the defective product. This warranty shall not apply to any damage, defect or failure caused by improper use or inadequate maintenance.

Certifications

CE Compliance

The TM-1020 series cameras have been certified to conform to the requirements of Council Directive 89/336/EC for electro- magnetic compatibility and to comply with the following European Standards:

Immunity: EN50082-2/1995

Emissions: EN55011/EN61326-1, Class A

All JAI, Inc. products bearing the CE mark have been declared to be in conformance with the applicable EEC Council Direc- tives. However, certain factory-installed options or customer-requested modifications may compromise electromagnetic com- patibility and prohibit use of the CE mark. Please note that the use of interconnect cables that are not properly grounded and shielded may affect CE compliance.

Contact JAI, Inc. Applications Engineering Department for further information regarding CE compliance.

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Oper- ation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

WARNING

Changes or modifications to this unit not expressly approved by the party responsible for

FCC compliance could void the user’s authority to operate the equipment.

TM-1020 Series Operation Manual Printing:May 31, 2007

JAI, Inc.

625 River Oaks Parkway San Jose, CA 951345 Tel:(408) 383-0300 Tel:(800) 445-5444 Fax:(408) 383-0301 E-mail: imaging@jai.com

www.jai.com

 

 

 

ATED

I

 

 

 

M

 

 

T

O

MA

 

U

G

A

 

I

 

 

N

 

 

 

G

 

 

 

 

 

 

 

MEMBER

A

N

S

IO

 

SOCIAT

FILE #

 

 

R

A3942 G U

 

R

® L

 

M

E

 

I

I

F

S

D

 

TERE

 

 

JAI, INC.

ISO-9001

Page 2 Page 4
Image 3
Page 2 Page 4
Contents TM-1020 Series Progressive Scan Shutter Cameras Page JAI, Inc CE CompliancePage Introduction Scan Modes Problems and SolutionsSpecifications Dynamic Range ControlList of Tables List of Tables List of Figures List of Figures Product Description TM-1020 Series Progressive Scan Shutter CamerasElectronic shutter Miniature size and light weightAsynchronous reset ImagerWarranty OutputIntegration TM-1020 Series System Configuration Components List Accessories and OptionsCamera Setup Heat Dissipation Getting Started Unpacking InstructionsConnector Pin Configurations 2 a 12-Pin Connector LVDS/RS-422 versionPin Connector LVDS/RS-422 version Description Pin Connector CL Version Description 2 b 12-Pin Connector Camera Link VersionDigital Output Connector LVDS/RS-422 only Analog Output Connector Manual Async Shutter Speed Control Dial LVDS/RS-422 version4 RS-232 Communication Cable LVDS/RS-422 version Shutter Speed Control DialDigital Output Cable 30DG-02 Digital Output Cable LVDS/RS-422 versionCamera Link Cable Camera Link Cable CL Versions OnlyPower Supplies and Power Cable Setup Power SuppliesJAI, Inc. Power Cables 12P-02S Interface Cable Pin# Lead Color Function Building Your Own Power CableAttaching the Power Cable to the Connector Attaching the Analog Video OutputAttaching the Camera Lens Mode Selection switch Shutter Speed Control switch 1 Up/Down SwitchMode Selection Switch Progressive Scanning Digital Output ConnectorAnalog Output Connector Power and External Sync ConnectorElectronic Shutter Stand-by Image Shutter Video Internal Shutter Speed Control TM-1020 Series Internal Shutter Speed Control TM-1020 SeriesNo-Delay Shutter Internal Shutter Speed with Fast Mode TM-1020-15 only Internal Shutter Speed with Fast Mode TM-1020-15 onlyInternal Shutter Speed with Slow Mode TM-1020-15 Only Internal Shutter Speed with Slow Mode TM-1020-15 OnlyExternal Vinit with Pulse Width TM-1020-15 Only External Vinit with Pulse Width TM-1020-15 OnlyCCD Output Voltage Programmable Look-Up Table LUT and Knee ControlLook-Up Table Full Progressive Scan Two-Row BinningExternal Sync and Pixel Locking Pixel Clock and Digital Data External Reset Timing Internal HD Async Shutter 0 Reset Timing Serial Communication Kit LVDS-Version Camera RS-232 Commands First Second Third Response Functions Character Symptom No Video Symptom Dark VideoSymptom Non-synchronized Video Information and Support Resources Power cable ResolutionPower requirement WeightTM-1020 Series Progressive Scan Shutter Cameras Physical Dimensions 1 TM-1020 Series Physical DimensionsSpectral Response 2 TM-1020 CL Series Physical DimensionsEmail imaging@jai.com
Top Page Image Contents