Toshiba IK-TF9U instruction manual Changing each setting in SS synchro. scan mode, Mode = SS

Page 14

(1. 2) Changing each setting in SS (synchro. scan) mode

Move up down

Set by pushing

By pushing

DATA UP, DOWN

MENU UP, DOWN

 

-- SHUTTER --

 

MODE

SS

SS

OFF

PART

OFF

<MODE = SS>

(a) Changing the shutter speed setting

Sutter mode MANU, SS, E.TRG

Synchro. scanning setting

OFF : 2H/1592H 1590H/1592HOFF2FRM512FRM

30fps, E.30fps : 2H/1060H 1058H/1060HOFF2FRM512FRM

40fps, E.40fps : 2H/774H772H/774HOFF2FRM512FRM

Partial scanning switch OFF/25fps/30fps/35fps/40fps/45fps/50fps/ E25fps/E30fps/E35fps/E40fps/E45fps/E50fps

1Set the "" to SS by pushing [MENU UP], [MENU DOWN] buttons.

2Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.

(b) Partial scanning setting

1Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.

2Select either the mode by pushing [DATA UP], [DATA DOWN] buttons.

Note:

The slow shutter speed may increase the fixed pattern noise and/or the white pixels. This is a charac- teristic of CCD, and is not a symptom of malfunction.

14

Image 14
Contents IK-TF9U Following information is only for EU-member statesSafety Precautions Disclaimer Table of Contents Components Names and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic Black Balance Result displayed Meaning Temp LOWItems Controlled by Using on Screen Display Available selectionsMode Setting by on Screen Display Using the MenusFlicker may be large MenusShutter Electronic shutter TRGPartial scanning setting Changing each setting in Manu modeMode = Manual Menu UP, DownChanging the shutter speed setting Changing each setting in SS synchro. scan modeMode = SS Changing the polarity of inputting trigger pulse setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR 1P SNR, 1P SR, PW SNR, PW SRChanging each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNRMode = E.TRG E.TRG = RR Changing each setting in PW SR modeMode = E.TRG E.TRG = PW SR Gain Video gain Changing each setting in GainChanging the gain in Manu mode WHT BAL White balance Changing master pedestal MANU/OFFChanging gamma correction Changing R pedestalSync OptionSetting by 2H Setting by the frameSetting to factory setting status Synchro. Scan OperationE. TRG External trigger 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing Fval Lval Dval1P SR 1 Pulse Trigger Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output TimingPW SNR Pulse width trigger SYNC-NON Reset Pulse Width Trigger SYNC-NON Reset Picture Output TimingPW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output TimingLong Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning OFF All pixels scanning When Partial Scanning Mode is onPartial Read Partial Scanning onExternal Sync External sync signal polarityUsing the unit with external sync signal External sync frequency rangeVertical Output Waveform Timing Chart Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Fval LVAL、 DvalSpecifications RGB, 3CCDSymptom Items to be checked External Appearance DiagramBefore Making a Service Call How to Obtain Warranty Service Step-By-Step Procedures Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts Your Responsibilities