Toshiba IK-TF9U instruction manual Sync, Option

Page 22

(4. 5) Changing the shading correction mode

1Set the "→" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.

2Set the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.

Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis- played in the menu.

(4. 6) Changing the manual shading correction setting

1Set the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.

2Set the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.

( 5 ) SYNC

When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically.

Move up down					Set by pushing
By pushing					Set by pushing
By pushing					DATA UP, DOWN
MENU UP, DOWN					DATA UP, DOWN
MENU UP, DOWN



		-- SYNC --

MODE	EXT
H PHASE
	0

•Sync system display

•H PHASE -100 to 100

(5. 1) Adjusting horizontal phase

1Set the "→" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.

( 6 ) OPTION

(6. 1) Changing serial communication baud rate

1Set the "→" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.

2Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.

Move up down By pushing

MENU UP, DOWN

Set by pushing

DATA UP, DOWN

-- OPTION --

BAUD RATE 9600

• Serial baud rate 9600, 19200

22

Image 22

Contents IK-TF9U Following information is only for EU-member statesSafety Precautions Disclaimer Table of Contents Components Names and Functions Connection Connector Pin AssignmentsStandard Connection Automatic Black Balance OperationWhite Balance Result displayed Meaning Temp LOWItems Controlled by Using on Screen Display Available selectionsMode Setting by on Screen Display Using the MenusFlicker may be large MenusShutter Electronic shutter TRGPartial scanning setting Changing each setting in Manu modeMode = Manual Menu UP, DownMode = SS Changing each setting in SS synchro. scan modeChanging the shutter speed setting Changing the polarity of inputting trigger pulse setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing 1P SNR exposure time settingChanging 1P SR exposure time setting Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR 1P SNR, 1P SR, PW SNR, PW SRChanging each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNRMode = E.TRG E.TRG = PW SR Changing each setting in PW SR modeMode = E.TRG E.TRG = RR Changing the gain in Manu mode Changing each setting in GainGain Video gain WHT BAL White balance Changing master pedestal MANU/OFFChanging gamma correction Changing R pedestalSync OptionSetting by 2H Setting by the frameSetting to factory setting status Synchro. Scan OperationE. TRG External trigger 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing Fval Lval Dval1P SR 1 Pulse Trigger Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output TimingPW SNR Pulse width trigger SYNC-NON Reset Pulse Width Trigger SYNC-NON Reset Picture Output TimingPW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output TimingInput Timing Chart Example RR Reset restartLong Term Exposure Partial Scanning OFF All pixels scanning When Partial Scanning Mode is onPartial Read Partial Scanning onExternal Sync External sync signal polarityUsing the unit with external sync signal External sync frequency rangeVertical Output Waveform Timing Chart Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Fval LVAL、 DvalSpecifications RGB, 3CCDBefore Making a Service Call External Appearance DiagramSymptom Items to be checked How to Obtain Warranty Service Step-By-Step Procedures Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts Your Responsibilities