Toshiba IK-TF9U Changing each setting in E.TRG mode, Changing each setting in 1P SNR mode

Page 15

(1. 3) Changing each setting in E.TRG mode

The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, PR.

First set the "" to MODE and select E. TRG, then set the "" to E.TRG and select the desired E.TRG mode.

(1. 3. 1) Changing each setting in 1P SNR mode

Move up down By pushing

MENU UP, DOWN

Set by pushing

DATA UP, DOWN

-- SHUTTER --

 

MODE

E.TRG

E.TRG

1P SNR

TRG.P

 

EXP.

50ms

PART

OFF

<MODE = E.TRG E.TRG = 1P SNR>

Sutter mode MANU, SS, E.TRG

E.TRG mode

1P SNR, 1P SR, PW SNR, PW SR, RR

• Input trigger pulse setting at 1P SNR and 1P SR

Input trigger pulse : positive polarity Input trigger pulse : negative polarity

• Exposure time setting at 1P SNR and 1P SR

0.01 ms0.02 ms0.4 ms1 ms20 ms50 ms

0.01 ms

0.02 ms

0.1 ms

1 ms

2 ms

step

step

step

step

step

Partial scanning switch OFF/25fps/30fps/35fps/40fps/45fps/50fps/ E25fps/E30fps/E35fps/E40fps/E45fps/E50fps

(a) Changing the polarity of inputting trigger pulse setting

1Set the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.

2Select either , by pushing [DATA UP], [DATA DOWN] buttons.

(b) Changing 1P SNR exposure time setting

1Set the "" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.

2Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.

(c) Changing the partial scanning setting

1Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.

2Select the mode by pushing [DATA UP], [DATA DOWN] buttons.

15

Image 15
Contents Following information is only for EU-member states IK-TF9USafety Precautions Disclaimer Table of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation Automatic Black BalanceWhite Balance Temp LOW Result displayed MeaningAvailable selections Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayTRG MenusShutter Electronic shutter Flicker may be largeMenu UP, Down Changing each setting in Manu modeMode = Manual Partial scanning settingChanging each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing 1P SNR exposure time setting Changing each setting in E.TRG modeChanging each setting in 1P SNR mode Changing the polarity of inputting trigger pulse setting1P SNR, 1P SR, PW SNR, PW SR Changing each setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Changing 1P SR exposure time settingMode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRMode = E.TRG E.TRG = RR Changing each setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance Changing R pedestal MANU/OFFChanging gamma correction Changing master pedestalOption SyncSynchro. Scan Operation Setting by the frameSetting to factory setting status Setting by 2HFval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing E. TRG External trigger1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanningExternal sync frequency range External sync signal polarityUsing the unit with external sync signal External SyncFval LVAL、 Dval Output Waveform Timing ChartHorizontal Output Waveform Timing Chart Vertical Output Waveform Timing ChartRGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked Your Responsibilities Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts How to Obtain Warranty Service Step-By-Step Procedures