Toshiba IK-TF9U instruction manual Manu/Off, Changing gamma correction, Changing master pedestal

Page 21

( 4 ) PROCESS

Gamma Correction (GAMMA)

Select either OFF or ON of Gamma Correction.

Master Pedestal (M. PED)

Set the Pedestal level of each RGB.

R Pedestal (R. PED)

Set the Pedestal level of Red.

B Pedestal (B. PED)

Set the Pedestal level of Blue.

Shading Correction (SHAD.)

Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of the screen. In this case, the shading correction can decrease the color shading. For the shading correction of the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided.

1MANU (Manual Shading)

Adjust the correction amount on the PROCESS menu by confirming with a monitor or a waveform monitor.

2OFF

The status is no shading correction.

*The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with SHAD. OFF for variable lens conditions.

Move up down By pushing

MENU UP, DOWN

Set by pushing

DATA UP, DOWN

 

 

-- PROCESS --

 

 

 

 

 

• Gamma correction ON/OFF

 

 

GAMMA

OFF

 

 

 

• Master pedestal adjustment -64 to 64

 

 

 

 

 

• R pedestal adjustment

-64 to 64

 

 

M.PED

0

 

 

 

 

 

 

 

 

R.PED

0

 

 

 

 

• B pedestal adjustment

-64 to 64

 

 

 

 

 

B.PED

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SHAD.

MANU

 

 

 

 

• Shading mode setting

MANU/OFF

 

 

 

 

 

 

MANU

0

 

 

 

 

 

 

 

 

 

 

• Manual shading adjustment -128 to 127

(4. 1) Changing gamma correction

1Set the "" to GAMMA by pushing [MENU UP], [MENU DOWN] buttons.

2Set the gamma correction by pushing [DATA UP], [DATA DOWN] buttons.

(4. 2) Changing master pedestal

1Set the "" to M. PED by pushing [MENU UP], [MENU DOWN] buttons.

2Set the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.

(4. 3) Changing R pedestal

1Set the "" to R. PED by pushing [MENU UP], [MENU DOWN] buttons.

2Set the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.

(4. 4) Changing B pedestal

1 Set the "" to B. PED by pushing [MENU UP], [MENU DOWN] buttons.

2 Set the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.

21

Image 21
Contents Following information is only for EU-member states IK-TF9USafety Precautions Disclaimer Table of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation Automatic Black BalanceWhite Balance Temp LOW Result displayed MeaningAvailable selections Items Controlled by Using on Screen DisplayUsing the Menus Mode Setting by on Screen DisplayShutter Electronic shutter MenusFlicker may be large TRGMode = Manual Changing each setting in Manu modePartial scanning setting Menu UP, DownChanging each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing each setting in 1P SNR mode Changing each setting in E.TRG modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingMode = E.TRG E.TRG = 1P SR Changing each setting in 1P SR modeChanging 1P SR exposure time setting 1P SNR, 1P SR, PW SNR, PW SRMode = E.TRG E.TRG = PW SNR Changing each setting in PW SNR modeChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRMode = E.TRG E.TRG = RR Changing each setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance Changing gamma correction MANU/OFFChanging master pedestal Changing R pedestalOption SyncSetting to factory setting status Setting by the frameSetting by 2H Synchro. Scan Operation1 Pulse Trigger SYNC-NON Reset Picture Output Timing 1P SNR 1 Pulse Trigger Sync Non ResetE. TRG External trigger Fval Lval Dval1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync ResetPulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESETRR Reset restart Input Timing Chart ExampleLong Term Exposure Partial Read When Partial Scanning Mode is onPartial Scanning OFF All pixels scanning Partial Scanning onUsing the unit with external sync signal External sync signal polarityExternal Sync External sync frequency rangeHorizontal Output Waveform Timing Chart Output Waveform Timing ChartVertical Output Waveform Timing Chart Fval LVAL、 DvalRGB, 3CCD SpecificationsExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked One 1 Year Limited Warranty of Labor and Parts Limited Warranty Toshiba CCD CameraHow to Obtain Warranty Service Step-By-Step Procedures Your Responsibilities